• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

• 페이스북 공유
• 트위터 공유
• 

How to Replace Window Panes

A cracked window pane can cause a lot of trouble. This can be an opportunity to upgrade to energy-efficient windows or insulated ones and enjoy advantages like improved comfort, higher resale value and reduced utility costs.

You can do it yourself at only a fraction of the cost it would cost to employ an expert. It requires the right equipment and an hour or two of your time.

Glass

If your single-pane windows are old, deteriorating or broken replacing them with modern glass that is tempered or insulated will increase energy efficiency and reduce noise while maintaining the original character of older homes. The replacement of windows is easy and can be accomplished by homeowners with basic hand tools. In addition to a new pane, the following items are required such as latex glazing putty; Glazier's points; pliers and a heat gun for warming the old putty, if necessary. Wear safety glasses and gloves prior to beginning. Working with broken glass replacement On windows could result in serious injuries.

Begin by removing any broken pieces of glass. It is best to use pliers however, a flathead may work as well. Use a wood chisel, or putty knife to get rid of any old putty that remains around the frame and window sash. Take your time and work slowly and be careful not to damage the old window sash. It is a good idea to do this on a sturdy ladder rather than the ground and to place someone on the sash to help hold it in place.

Once you've removed all the old putty, it is time to prepare the window frame to fit the new pane. Take measurements of the width and height of the opening in the sash by subtracting 1/8 inch from each measurement (to allow for seasonal expansion and contraction). Bring these measurements to an hardware store or home center and find a piece glass cut to size. Alternatively, you can cut the glass yourself, if you have the tools you need.

After putting the new pane in place, run a small bead of caulking along the edge to seal it against weather. Install a glazier's pointing on both sides of the frame. This will ensure the pane. The points should not be so tight that they cause friction between the sash and frame but they shouldn't be loose.

Before applying the putty knead it thoroughly until it is smooth and free of lumps. Cut it into pencil-sized pieces. Apply the first strip to the corner of the frame. Work from one corner to another and ensure that it is even and smooth.

Glazier's Points

The glazier’s points are small triangular pieces of metal which help to secure the glass to the frame without causing any damage to the fragile surface. Knowing how to use these tiny helpers is simple and can save you money on professional installation or the cost of buying new glass.

After the old putty as well as the glazier's points have been removed Clean the frame thoroughly using a utility knife to get rid of any remaining residue. If necessary it is necessary to lightly sand the wood along the grooves of the rabbet to smooth out rough spots. If you sand wood, protect it with painter's tape to prevent accidental damage.

Take the dimensions of the frame and note down precise measurements. These dimensions can be taken to the hardware or home center store, and the new pane will be cut a bit smaller. This will ensure a tight fit and leave room for expansion and contraction.

Place the new pane in the frame and push firmly using your hands. Then, you can use the point of your chisel or the back of the putty knife to tap in the glazier's points as shown in Figure 11. After you're done, the points should be flush with the top edge of the pane and the shoulders of the points should be below the rabbet's lip. groove.

Apply a thin bead of glazing compound on the edges of the glass that has been made and into the rabbet grooves, to seal and protect them. Allow it to dry and cure fully.

When the glazing compound is dry and the glazing compound is dry, you can install the new window sash. First, you need to coat the wood with a thick layer of linseed. This will prevent the new putty from sucking up moisture and deteriorating and cracking with time. Apply this coat using a brush or the tip of your putty knife, then employ the chisel or back end of the putty knife to gently hammer in the new sash and glazier's points into the grooves of the rabbet. Repeat this procedure every 10 inches around the frame's perimeter.

Putty

A baseball hit or a rock thrown by error or a branch falling could result in a broken or cracked window replacement glass near me pane. Fortunately, the majority of windows can be easily replaced by simply placing a new piece in the right place. The glass is held in place with a small metal clip called a glazier's point, and putty, also called glazing compound. Remove the old pane and clean the area using a rag, a pull-type scraper, or a wood chisel. Wear protective glasses and gloves while working. You'll need a heating gun when the window is fixed to the frame.

If you're planning to install the original sash, remove any pieces of molding that secure the old pane. Sand the sash until it is flat and ready for new caulk. After the sash has been put back in place then, you can apply a silicone caulk over the glass. This will ensure that it doesn't be leaking or fade over time.

Take out the glazing points in the rabbets. These are the grooves in the sash, where the glass is located. If they're difficult to work out, try placing a hand tool like a heat gun over them to soften them up first. If you're using a heated gun, be cautious not to damage the railings or sash by holding the tool too close.

After the old glazing points and putty have been removed prepare a bed for the new pane. Roll a piece of glazing compound between your hands, forming it to be about 1/2-inch thick. Press it into the rabbets, where the glass will be put. It's important that the glass is positioned against the putty on each side So if you have to do so, gently tap the glass into the rabbet with your thumb.

If the new pane has a crack then you can seal it with a solvent-based glass glue or silicone caulk prior to pressing it into the sash. If the crack is not sealed, you'll need to apply putty to keep the water out. After the putty has dried and the film is oily, wipe it off the glass using an abrasive and allow it to dry completely prior to painting. Paint before the putty has completely dried. It won't form a good seal and could leak or discolor with time.

Paint

You may be concerned about replacing a broken piece of glass. The truth is, replacing a single piece of glass doesn't need to be expensive even if you do it your own. Even a double-paned window can be replaced at a fraction of the cost it will cost a professional.

If you are working with a large glass window first ensure it is securely attached to the frame. This can be done relatively easy and quick with the proper tools and techniques.

When you're ready to start, begin by removing the old window by removing the glazing points of metal that are attached to it. These are tiny triangles of metal that function as "nails" to hold the window within the frame. They are buried beneath a bead or glazing glue that sets to form solid wedge that holds the wood frame securely in place and hides the points.

After removing the old pane, clean the frame and the wood. Scrape away any paint and sand down the rabbet grooves where the glazing points used to be. Sand them to bare wooden surfaces, allowing you to paint the frames the same shade. After sanding, apply a coat of flax oil on the bare wood to extend the life of the frame.

Next, measure the dimensions of the window's opening. You'll need to determine the vertical and horizontal dimensions of the entire opening, as well as the thickness. To get the exact size of the new pane, subtract 1/8 inch from both measurements. This will allow for seasonal changes in the glass. You can bring these measurements to a hardware store or home improvement store and have the glass cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.