• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

• 페이스북 공유
• 트위터 공유
• 

How to Do a Door Lock Change

The change of your door lock is a simple and inexpensive method to increase the security of your home. The process is not for everyone. It requires a certain amount of patience and expertise.

It is necessary to replace the cylinder that is inside the knob's body. The cylinder is responsible to recognize the key when it is inserted into the lock.

Take off the lock that was previously used.

The first step in replacing the door lock is to get rid of the lock that was previously in use. It's a fairly simple process, however there are a few points to remember. First, ensure that the lock you choose to install is the correct size for the door you have. This will ensure that it fits securely and doesn't leave a gap in the deadbolt plug or latch.

After you've removed the latch plate look for two screws or bolts on the inside of the casing that connect the casing and two halves of the lock together. Unscrew these with a screwdriver, then remove the lock from the door. If you have a mortise lock there might be a set screw located at the base of the handle that binds it to the spindle. Take off the doorknobs by removing this screw with the help of a screwdriver.

You must also remove the deadbolt latch and latch plug from the hole in the door jamb. Install the new lock. If you're replacing a mortise, you should determine the distance between your lock case and your door edge to ensure that the new lock will fit.

You may want to replace your lock for various reasons, such as if you suspect that someone else has the key, or if you have an incoming roommate. In any event, you could save money by taking the lock off yourself rather than paying an expert to do it. It's easier than many people think and can be completed in a few minutes.

Remove the trim and handle of your door. Then, pull the trim loose using a screwdriver that is flat. You will be able twist off the majority of it and in some cases the handles may fall off entirely. Then, look for a tiny hole on the inside and insert a straightened clip into it. This will trigger the release mechanism, allowing you to remove the handle. Look for a small tab that is located inside of the lock, and press it using a flat screwdriver. After the spindle is removed, you can remove the housing and cylinder.

Making a choice for a new lock

There are a lot of options available when it comes to selecting a new lock. Consider the different types of locks and pick one that is in keeping with the design of your door. Think about the backset, which is the distance between the edge and the center of the hole for the lock. Also consider the cross bore, a tiny hole that is located at the edge of your door frame. Also, make sure to choose a window lock replacements that will fit the door thickness and swing.

The American National Standards Institute and BHMA have graded all door locks to give you an idea of their durability and how difficult it is to pick them or disable them. A grade 3 lock might be the best choice for a peaceful suburban apartment complex, whereas the grade 1 lock may be more able to withstand the traffic that is frequented by a retail storefront on a busy street.

Most smart door locks require a digital key code to open. If you're worried about security breaches or hacking you should consult an expert locksmith or your local police department for assistance.

Replacing the cylinder

It is easy to replace damaged or broken door lock cylinder with a simple DIY project. It is important to select the appropriate cylinder and follow all instructions. The first step is to remove the knob or handle should there be one and then remove the trim that is attached to the base of the lock cylinder by using the aid of a screwdriver. After the trim is removed, you can reach the screws that hold the cylinder in place and remove them with a flathead screwdriver. The cylinder can then be gently removed from the door.

Be sure to measure the length of the new cylinder prior to installing it. With a tape measure, determine the distance between the center of the cylinder and the left and right sides. Then, purchase a new cylinder with the same measurements. This will stop cylinders from snapping when the door is hit or the key is stuck inside.

Install the upvc replacement window locks cylinder into the door and then turn the key. This will align the cylinder with the carrier that is usually located on the outside of your lock. Then, you can loosen the set screw that is supposed to be a few turns in the head. You will also need to loosen the screw on the door's edge which secures the case should there be one.

You can replace the cylinder that was used to window lock replacement near me your old lock with the new one by slipping it into the case, and then tightening the set screws. It is also recommended to reinstall the piece that connects the cylinder with the lock indicator stem that you can do by pulling out three tabs on the back of the cylinder using needle-nose pliers. Attach the bracket that is smaller to the back of the cylinder. Then, you should install the strike plate and latch plate, as well as the retaining ring attached to the top of the lock cylinder.

Installing the new lock

If you're replacing an old lock, you must begin by measuring the width of the door. Most locksets for residential use are designed for a door thickness of 1 3/8 to 1 3/4 inches. If your door is more thick, you will need a door kit that is thick and includes longer screws as well as longer tail pieces (for door knobs) or spindle extensions (for deadbolts).

Most double glazing Window locks repairs come with a thorough installation guide to aid you. Read the instructions carefully before starting the process to ensure that you've followed all the steps. The guide will give you a clear idea of how much skill is required to complete the task. If you're changing locks for the first time, you might want to ask an experienced person for help.

It's a great idea to cover the holes in the old hardware before installing the new lock. This will stop the screws from slipping through the holes and will also protect any tiles you may have installed. It will also protect your tiles from damage caused by rust, dirt and grime. SECURAM Touch includes an ad-hoc strip of masking tape or gaffer tape. However, you can make use of any tape you have.

After taking off the screws that connect the lock's inner half to the outside then take the lock off immediately. This must be done quickly to prevent the lock from accidentally closing and harming the mechanism.

Fit the new latch bolt into the upper cross bore of the new lock, if it comes with one. Make sure that you place it in the correct position, which will be indicated by an arrow. Next, fit the latch plate on top of the bolt and secure it in the correct position.

Screw the deadbolt into the jamb of the door. Check the deadbolt several times by throwing it to ensure it is extending into the strike plate. If you're using an electronic smart lock, make sure to follow the instructions to program it. This involves downloading an application, registering your e-mail address, confirming your identity, and connecting to the wireless network in order to connect your device.