• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

• 페이스북 공유
• 트위터 공유
• 

Patio Door Lock Repairs

Over time, patio doors experience wear and tear that can result in locks that fail. There are a few simple steps you can take to ensure the security of your uPVC door.

These easy fixes will ensure your home is secure regardless of whether you re-align the lock or clean the mechanism.

Clean the Lock

Patio doors are ideal for bringing the outdoors in and keeping the elements out. However they can pose risky for security when the lock isn't functioning correctly. As time passes wear and tear, hot and cold weather, dirt and debris can cause damage to your patio door's lock and cause it to become difficult to open. With a little care, you can make sure that your patio door's lock is always working correctly.

To begin with, it's essential to clean the lock of your patio door and all the moving parts. This will help get rid of any grime and coatings that could be preventing the lock from working as it should. Start by wiping all the moving parts on your patio door lock using a damp cloth. Then you can use a scouring paper or rough damp cloth to scrub the areas that are soiled of the door and frame. Then, wipe the entire lock using dry cloths to eliminate any remaining dampness, and allow it to dry completely before using it again.

If your patio door uses pin-tumbler latches you can lubricate it by applying powdered Graphite on the key. You can also use a Teflon lubricant such as WD-40 Multi-Use Product. This kind of lubricant can be applied quickly and doesn't dissolve over time. If you're unable find the right lubricant to use with your lock, you can make use of a pencil with a larger tip. Insert the pencil into the lock and move it around to spread the graphite.

Regular maintenance is also essential to keep the tracks of sliding patio doors clear from dirt, dust and other debris. They are particularly susceptible to snow, ice, and other particles, which could cause them to block or become stuck. This could make it difficult for your patio door to be opened and closed.

You can clean the track rails and rollers on sliding patio doors by removing any weather stripping that is dirty or damaged. Clean it, and then replace it. The same is true to patio door rollers which can be cleaned and sprayed with a non-stick lubricant to help them move freely.

Lubricate the moving parts

uPVC French Doors, like sliding patios, are operated using 3 to 4, or sometimes, 5 point locking mechanisms. They include the handle and lock cylinder which is operated by the key. These doors require maintenance, the lubrication of moving parts. This can be accomplished using a thin oil (never WD40) and should be done every year.

If hinges that are sagging aren't the cause, the door may be skewed and catch or striking the strike plate's hole in the frame. The solution is to take off the strike plate and then use a sharp chisel to enlarge the mortise it rests in. This will allow the latch to fit into the hole and stop it from scratching against the frame.

Once the cylinder is cleared of the way and out of the way, measure its width using an object or a piece of wood that fits into the gap of adjustment screw above the lock. The outer dimension is measured from the outside of door to the center of cylinder. The inner dimension is measured from the center adjustment screw to the end of the cylinder.

Check the Lock's Width

If your patio door latch isn't able to turn, even after cleaning and lubricating, it's possible that it's out of alignment with the strike plate hole. Examine if the door is balanced and if the hinge screws are secure, but in many cases, moving the strike plate up or down can fix the issue.

The latch may not engage properly when the strike of the lock is too small. In this case, enlarge the opening using the hammer and chisel. Then test the latch to ensure it does not rub against the jamb frame of the door or get caught on it.

Before buying a replacement lock, first identify the type of mortise lock you currently have. This can be done by looking at the faceplate on the lock and noting if it is round or square. Take a look at each screw hole on the current lock and note the size. This information will allow you to find the replacement lock that has the exact same width and will fit into the hole that you already have.

In addition to identifying the current mortise lock you'll also want to inspect it for any scratches or bends that might require repair. A badly bent or damaged latch is more likely than one that's been used a lot to break. Replace the lock if it shows indications of damage.

Once you've decided on the kind of lock replacement you need It's time to start the actual repair. Remove the handle and spindle from your patio door, and then install the new one. Begin by installing the handle in the interior and aligning it with the spindle, and then fixing it with the two screws or bolts that secure it. Install the exterior handle after the interior handle. After you've completed these steps, test the handles to ensure that they can be shut and open easily and that the latch works correctly with the strikeplate.

Check the Strike of the Door.

The door latch and strike plate are two components of the lock that work to ensure that the latch locks the door. If these are misaligned and the latch doesn't latch the door shut correctly. Fortunately, this issue is usually easy to correct.

First, inspect the holes in the strike plate's receiving to make sure they are clear of obstructions such as dirt or plastic plugs. Then, loosen the keeper screws that keep the strike plate in place and allow it to move vertically but not separating it from the door frame. Then, adjust the strike plate to ensure that its receiving holes align with the latch hooks on the door latch. After the strike plate has been adjusted tighten the screws, and then test the door to determine if it shuts smoothly with the new adjustment.

Door strike plates can be a bit difficult to access for homeowners who have sliding patio doors, however they're essential to lock and unlock your door. The metal plates are situated on the top and bottom jambs of the door where they serve as the support for the latch. The door latch slides into the strike plate to form the seal when it is closed. If the strike plate is damaged or rusted, or if it is not properly installed, the latch may not be able to lock the door properly.

A misalignment between the latch and strike plate is a common reason for the patio door glass repair near me lock to not close or stick. The easiest way to check for this is by performing the "lipstick test." Apply some lipstick along the edge of the deadbolt, then attach masking tape over it. When you shut the door, the lipstick will leave an impression on the tape, indicating you exactly where the latch contacts the strike plate. If the mark is too low or high, you can alter the strike plate.

The sliding patio door locks keep your home safe from burglars. If they're not functioning correctly, you should repair patio door lock the issue quickly. By following these easy steps, you'll be able to fix the lock on your patio door and get it back to normal within a short time.