• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

• 페이스북 공유
• 트위터 공유
• 

How to Repair Bifold Door Top Roller Guide

If your bifold door is squeaking then it's likely that they require some maintenance. They might need to be cleaned, lubricated or adjusted. The problem could be caused by a loose bolt on the top pivot or by the top guide roller.

This kit includes everything you need to restore your bi-fold wardrobe door system to its optimal performance.

Take the door off

It may seem complicated and challenging to put in a set of bifold internal doors, but for DIYers with a little experience, it's actually a breeze. The frame's placement isn't a major issue The trick is getting the doors to fold and close easily and precisely. Bifold doors are a complex piece of machinery, and as such they may require some 'tuning up' to ensure that they function properly. It could be as simple as tightening up a screw, or as complicated as removing and replacing the pivot pin or roller.

You can usually resolve these issues with a few simple adjustments, without the need to take off the doors. You may notice that your doors are sliding or scratching the floor, or they are bouncing off of their track. It's not difficult to fix these issues. Just follow three simple steps and your bifold door should be back in line in no time.

One of the most frequent problems that internal bifold doors face is that they are sliding out of alignment. This could be due loose screws, holes in the anchor/pivots, or a misaligned bifold door. Most of the time it can be fixed by a few simple adjustments. However, if your door doesn't move in any way, you might need to replace it.

To open the door, you'll need an screwdriver and perhaps pliers (to help loosen any pins that are tight to pivot). The screwdriver is used to disengage the locking levers on the bottom bracket for pivots. The pliers are used to remove the pin.

Once the top roller is removed After that, you can lift the door, swivel downward and remove it from its track and pivot brackets. It is usually a simple process, but you must be cautious not to let the door hit the frame of the door. You'll then be able to saw off the edge of the door which is scraping the floor, and sand it down until it's smooth. Then paint or refinish the door if required.

Remove the Roller Guide

This spring-loaded roller guides mounts on the top of bifolding doors to aid in smooth operation. It is designed to be used with Kenna frames and can be fitted to doors that are 1 to 1/8 inch thick. It is made from nylon, steel and plastic components. It can be used to replace a worn-out or damaged guide.

To begin removing the roller guide, remove the screws that hold it in place by using a screwdriver and a bit to loosen it. Then, carefully use your hands to lift it out of the frame. It might require some effort to take off the door, so you may need a friend to help you.

Once the guide you used to guide your child is removed, carefully cut the remaining finish on the foot of the new guide with the help of a razor blade to separate it from the rod blank. This will make the guide foot easier to remove and will prevent any damage. The foot is extremely sharp, and it could cut or snag fingers.

You may have to use some force to remove the guide, but you must be careful not to break or chip the foot. Once you have removed the guide from the rod blank, be sure to remove all of the epoxy and threads that remain in the place the guide was attached. This will prevent future problems with the guide.

After removing the guide, you can test the replacement by putting it in its permanent position. Apply a few rotations using masking tape or guide tubing to hold it in position. This will allow you to double-check the alignment of the guide and spacing to ensure everything is set up correctly. This is vital to avoid any issues in the future regardless of whether you use the CRB Spine Finder and Deflection System, or just eyeball it.

If the guide is positioned correctly and functioning as it should then the final step is to reinstall the door in its place. Remember to replace and tighten any screws or pins you removed or loosen.

Remove the Bottom Pivot

bifold door glass replacement doors can be a beautiful feature for a home, but they often need to be tweaked or adjusted to ensure they are in good working order. Some issues can be resolved by keeping the doors in place. Others will require the doors be removed. This guide will demonstrate how to take off the internal bifold door replacement door pins, rollers and pivots.

The first step is to gather your tools. Making sure you have everything in place ahead of time will save you some frustration later in the process. You'll also require an plier and a screwdriver. You can pick up an assortment of basic tools at your local hardware store for a reasonable price. Keep a supply of wood glue in your kit. This is useful if you need to glue the rollers into place.

After gathering your tools then open the bifold doors and loosen the top track bracket with your screwdriver. Once this is loose the door should be able to slide off the top track completely. It could take a little bit of jiggling but it should be able to pop right off the track.

The bottom pivot of the frame will need to be removed. Close all interior doors before beginning. This will be a lot easier than working from the inside. If the track on the bottom appears to be in good condition you can lift the door up and remove the track.

If the track is damaged, you'll have to replace it. You can buy new tracks for swinging and bifold closet doors from a local hardware store. If the track is seriously damaged, you might need to replace it completely.

Once your track is repaired or replaced it is time to check the doors for proper operation. Verify that the doors move in and out of their positions smoothly. You should also ensure that the edges of the door are parallel to the frame when it is closed. If they're not, you'll need to readjust the top pivot bracket and tighten or loosen the bottom setscrew until the edge of the door is perfectly aligned with the frame.

Replace the Roller

When they are properly installed, bifold doors can neatly protect pantries, laundry rooms and closets. bifold door repair doors comprise two panels that are hinged and slide along a track at the top of the frame. Over time, the roller guides can wear out and cause the doors to bow. The roller guide can be replaced in a matter of minutes with the use of basic tools.

The first step is to take the guide for the roller from the door panel. This involves removing the bottom pivot bolt and loosening the screw that holds the guide at its top. After taking off the guide, pull the panel out of the track. Next, loosen the nut that holds the top pivot bolt and employ the wrench to pull it out of the hole in the top header of the door frame.

A replacement top nylon roller guide with a 7/8 " diameter wheel and a steel base is available from Stanley, Cox or Acme. It mounts on the top of a bifold door that is 1 to 1-3/8 inches in thickness and comes spring-loaded to self-adjust in the upper track for smooth gliding.

A bifold door can also scratch the floor when it opens and closes. This is often the result of adding carpet or other flooring materials that require the doors to be raised slightly for proper clearance. Removal of the bottom pivot adjustment screw and loosening the top track's mounting screws and moving the anchor/pivot pin is typically enough to resolve this issue.

A set top roller with new guides can be an inexpensive solution to your repairing bifold doors doors becoming difficult to operate. They're usually available at your local hardware store in the door section, but they're also available online from a number of suppliers. Along with a brand new top guide for rollers, you'll need a small container of Elmer's wood glue which is sold in the big box stores and a squeeze clamp. The clamp assists in keeping the repair area in place after glue is inserted and allowed to dry.