• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

• 페이스북 공유
• 트위터 공유
• 

Cat flaps let your cat go in and out at their own pace, without having to let them in or out. They also can help to stop your cat from urinating in the house.

Fitting a cat flap in a upvc door panel is a lot easier than glass doors, however it requires some knowledge and the appropriate tools.

Measure the Door

fitting cat flap in upvc door panel a cat door in the front door is difficult however, as long as the cat flap is the appropriate one and you follow the guidelines you can make it less difficult. We will help you draw the shape and then use the jigsaw to cut the door's area. Then we will finish the job by attaching the cat flap. This will ensure the flap is in place and protects the doors from the damage caused by rain and wind.

The first thing you need to do is take a measurement of the width of your pet in order to determine an accurate estimate of what size of cat flap you will require. This will enable you to select a cat flap that is large enough for your pet to go into the house and exit without needing to open the door every time.

If your kit comes with a drawing showing where to drill, you can put it on the door, and then draw around it. If your door has a sill or moulding at the bottom, be sure you leave enough space between your cat flap installer and these elements.

Then put on your eye protection as well as a dust mask, and using a jigsaw begin to cut along the line that you penciled in, but don't press the blade too hard because this can make it cut faster than you would like it to. Set the square with a ruler to ensure that you are cutting the material properly and that the cut is a rectangle shape. When you are satisfied with the result, you can remove the remaining door material.

Draw a Line

The cat flap lets you to let your pet inside and outside without worrying about unwanted visitors or unwanted gifts. It also prevents drafts and helps keep the temperature of your home steady. However, putting the cat flap to your door might seem like an intimidating task for those who haven't done it before, leading many people to seek out a professional carpenter or joiner to do the job instead. This is an option but you can do it yourself if your tools are right and the instructions are followed.

This is much easier to accomplish on wooden doors, but it is still possible with uPVC. However, you must be careful not to harm the doors because this will cause the door to be damaged and invalidate your warranty. First, you need to take measurements of the door to ensure it will accommodate the new cat-flap. If you have an ordinary uPVC panel it should be a breeze. However, if your door is made of composite or another kind of door, you might need to be more careful.

Next, you will need to determine the belly height of your cat. This is the amount of height between the floor and the bottom of your cat's stomach. You'll need to locate an area at the entrance that allows your cat flap bifold doors to pass through comfortably. Once you've figured out the measurements you'll have to mark the area using a spirit level and a pencil, so that you know the opening will fit your cat.

After you have marked the area, it's time to cut the hole. You will need to use a jigsaw and it is important that you take your time in order to ensure that the cuts are clean and smooth rather than uneven and rough, as this could damage your door. Wear safety glasses and a dust mask while using the jigsaw. Inhaling sawdust is dangerous for your health. After you've completed the cutting process, you will have to smooth the edges of the hole with sandpaper so that your cat flap will fit easily.

Cut a hole

Installing a cat flap into an existing door panel or double glazing sealed unit is quite difficult. You might be tempted to do it yourself, but unless you have a lot of experience in DIY it is likely to be best to have a professional in to do the job for you. A botched job could not only be unsightly, but also pose a security threat. It could let cold air in when the cat flap installer is outdoors and hot air to escape when the cat flap installer near me is inside.

The first thing you need to do is draw the position of the hole in the door with an eraser and an ax level. This will ensure that it is positioned and that it runs parallel to other parts of the door. You should make sure you have an sandpaper piece on ready to smooth any edges.

Wear any safety gear you require when working with an electric tool. If you are concerned about the sound produced by the jigsaw, you can purchase an electric version that is much quieter and easier to use.

It is important that you only remove the material required for the fitment of the cat flap. It is important to leave a bit of material to make the wall thickness of the cat flap. However cutting away too much could cause issues or even damage to the door frame.

A door made of upvc may include a metal frame, or panel that could interfere with the microchip cat flap, and if this is the case you'll need to cut an over-sized hole to ensure that the metal doesn't get in contact with the the cat flap. If this is the case, it is crucial to fill in the oversize gap and render it watertight.

If you are fitting a cat flap into the frame of a double glazed windows with a frame made of metal, you'll need to talk to a professional who can provide you with a new pane of glass that already has the hole for the cat flap premade inside. This will be less expensive than trying to install a cat flap in an existing pane that was not designed for this purpose.

Install the Flap

Cat flaps allow your pet the freedom to move around whenever they like, allowing them to relax in the home whenever they'd like. If you have an uPVC front door, it might be difficult to install the cat flap. This is especially the case if you do not own glass panels that is cut. If you are willing to install a half-glazed uPVC replacement panel, it is possible to add a cat flap. It's not just a matter of cutting holes in the door. It is also necessary to do a few things to ensure that it is safe.

A composite, uPVC, or GRP door panel is typically made up of a flimsy plastic outer skin joined to a soft polystyrene insulating core. The material is quite fragile and care must be taken when cutting into it to avoid causing damage. This type door comes with a template that can be used to cut the hole.

Once you've determined the location of the hole in your door, now it's time to put in the cat flap. You can purchase and install many different models, from basic push-button operated models to microchip activated units that allow access only to your pet. However, regardless of what type of cat flap you pick, it's important to make sure that your cat can use the flap without getting stuck outside in the rain.

A circular fitting is more effective than a square, because circles can be cut more securely into glass. It's because square holes are more likely to break the glass when drilled. It's also a safer option to use as you're not putting yourself at risk by having to drill into toughened glass that might break and cause injury to your pet or family members. This is especially important if you have a child or elderly person at home who could be injured by shards glass.