• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

• 페이스북 공유
• 트위터 공유
• 

How to Repair Car Keys

Car keys may seem small and insignificant, but they are crucial to the operation of your vehicle. The cost of replacing the traditional or modern transponder car key can be upwards to $200.

There are methods to fix your car keys at home with a fraction of the cost. This article will cover some of the most frequent car keys issues and their DIY solutions.

Dead Key Fob Batteries

Cars come with a remote key fob which makes opening doors, trunk and tailgate easier than ever before. However, the battery inside the device can fail. There are a few tricks you can use to solve this problem quickly.

First, determine if the car is in ignition mode. If it is, the key fob's battery could be low rather than dead. To test this, press the button on the fob against the ignition button of the vehicle. If it works, the battery is probably fine and needs to be replaced.

To replace the fob battery, first pry the case open using a screwdriver or watch-type tool. Be cautious not to press too hard because this could cause the fob's to split in two. If the fob isn't opening open easily, try wedge your pry tool in several places on the outside of the case.

After the fob has been opened take out the mechanical key and then open the electronic part of the car. Then insert the replacement battery and then snap the shell together. If the auto key repair near me fob doesn't work after this, there could be a bigger problem with the remote start system that requires a professional to diagnose. A reputable mechanic will capable of helping you in this situation. You can also contact roadside assistance for help with your vehicle if needed.

Broken Key Ring

If your key repair fob won't work because the ring is broken, there are a few things you could try. Look to see if can locate the broken piece in the ignition. If it's still there it, remove it without damaging the ignition lock or the door lock. Contact a locksmith if are having trouble getting rid of the key. They have special tools to safely remove a damaged or broken key from the ignition.

A broken car key can also be the result of corrosion on the plastic frame or circuit board. It is possible to clean the circuit board using the help of rubbing alcohol and a cotton swab. This will remove the corrosion and protect to the contact pads.

If your key isn't starting because the ring broke it, you might be able fix it with a strong wire or nail to seal the hole. You can also use superglue to repair a damaged ring. After cleaning the ring with a moist cloth, apply a small amount superglue to each end of the wire or nail. Press the pieces together and let them dry prior to using your car key button repair. These DIY solutions may seem appealing, but they're only an interim measure. It is recommended to hire an experienced locksmith for long-term repairs. They have the expertise and tools to repair the broken key quickly and efficiently. They can even replace the battery in your key fob and reprogram it if needed.

Broken Key Blade

Some key blades may break due to wear and tear. If this happens, you should probably buy a new blade. Fortunately, the issue isn't as bad as it may appear at first. The primary issue is that the metal blade broke off from the case.

One way to fix this is to spray the key hole with fluid that lubricates the key hole. You can then employ pliers or tweezers grasp the broken end of the key and pull it. If the key is magnetic, you could also try using a magnet to pull it out. Use a magnet as a aid to you remove the key, but take care to not sever the lock tumbler.

Call a locksmith immediately in the event that you are unable to remove the broken part of the key. They're equipped with special tools that can safely remove keys without causing damage.

Super glue can be used to fix the snapped lock. Apply a small amount of glue to the edges and press them together. Then, wait until the glue has dried before inserting your key into the lock. However, this method isn't reliable and you might have repeat the process several times before it's successful. In addition, the super glue may not be strong enough to keep the key in place. So, this is more of a stopgap measure rather than an option that can last.

Broken Plastic Loop

If the loop of plastic on your key fob breaks it can make the key ineffective. This is a relatively easy fix. As a replacement, you can use wire that is thick or a finishing nail. For each end of the nail or wire make two holes in the plastic loop. Cut the wire or nail to a key width, then put a drop of superglue in each hole. Put the nail or wire into the holes until it closes them, and then let it dry.

Another option is to purchase the replacement shell from a locksmith who sells them. They can transfer the programmable section of your key to the new shell and cut a brand new blade for less than the cost.

This is not the best option, but it can allow you to travel again if your key been cut in half. However, it could be difficult to repair the blade of the key if it's in the ignition. You could try using a hair clip or needle extractor tool to remove the damaged part of the ignition, but this is risky if you're not cautious. Contact a locksmith who has special tools to safely remove damaged keys from ignitions. They can also design new keys with the correct cuts for the ignition of your vehicle and ensure it works properly when it is inserted into the lock.

Broken Master Key

If a key is broken inside the lock, you'll need to try to retrieve it before it's completely destroyed. You can use tweezers, lubricants, and needle nose pliers to grab the broken fragment of a key.

To begin, spray the inside of your lock with a lubricant like graphite powder or WD-40. You can also employ the hacksaw blade method that involves sliding the blade along the side of a damaged key and grabbing onto some of its teeth. If you're successful then you should be able to remove the broken key.

Another tool that is useful is a spiral key extractor that is available in a variety of hardware stores. It is a thin, flexible bar with spiral threads which can be put into the keyway and bent to dig into the broken section of the key. Once it is firmly anchored to the serrations you can twist the bar into a circle and pull it against the damaged section of the key.

It's worth trying to get rid of a master key car repair that's broken prior to calling an expert locksmith. If you are unable to remove the broken piece, you'll need to call a locksmith. A locksmith can make you a new key that can be programmed with the transponder in your car.