• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

• 페이스북 공유
• 트위터 공유
• 

Replacement UPVC Door Handles

If you're replacing the handles or want to add a bit of extra security, you'll choose the perfect handle for your door. Upvc handles for double glazed doors are simple to fit and comply with the 92mm centers required by multipoint locks.

The most important measurements to be considered are backplate fixing centres and lever/key hole dimensions. Compare these measurements carefully with your existing marks before ordering.

Lever/Pad

Lever pad handles consist of a lever on one side and a handle that is shaped like a paddle on the opposite. They are designed to be used with key wind locks however, they can also be fitted to split spindle multipoint door locks (though you will need a separate dual spindle lock case).

After you have picked the correct handle for the doors, the available finishes will be shown in the drop-down list. Not all styles of handle are available in every finish and you should always check the sizes and technical drawings for the specific product you're looking for to ensure that you are getting the correct size and fitting.

It is crucial that when selecting a new set upvc lever pad handles, they match the PZ (distance from the spindle of the handle to the middle of the hole of the cylinder) of your multipoint door locks. This is because they must be lined up so that the doors remain locked, regardless of whether you are looking from the outside or inside. Our handles are designed to fit the majority of standard cylinders, but it is always worth double-checking before ordering.

You'll need to remove your handles that you have already installed and then dismantle the lock case if you're upgrading to dual spindle levers for your handle because this will require a split cylinder inline. You can purchase these separately. We have included a technical illustration in the images of each product.

It is a good idea to loosen the screws holding your door handle, and then check the mechanism. If the screws are too tight it is possible to loosen them even more. Then, you can remove the spindle from the door handle and replace it with your new upvc handle. Before putting the handle in place it is recommended to make sure it is in the correct position. You can do this by putting your finger in the space between the door frame and the door handle to make sure that it is in a level position.

Lever/Lever

The lever handles for doors are used to operate a multi-point lock that uses an Euro cylinder. They are found on a variety of double upvc doors as well as wooden and aluminium door handle doors. They come in two varieties, with a lever on the interior and a paddle on the outside. Sprung - These have an internal spring cassette within the backplate, which helps to bring the handle lever into the horizontal position. Non-sprung: These do not include a mechanism that can spring the handle lever to a horizontal angle.

To fix the door handle of a lever that is sagging you must locate the detent access hole or pin, which is typically a small round or rectangle shape hole or protruding pin that is located on the opposite side of the handle base plate. Once located you can loosen the set screw with a screwdriver and take it off to allow the lever and return it to the horizontal position.

Once the handle is placed horizontally, you can put back the screws. Tighten them to ensure that the handle remains firmly attached to the base plate. You should also consider applying a threadlocking adhesive solution to the threads of the screw to increase the grip and prevent them from loosing over time.

There are a variety of reasons why door handles of levers droop. The most frequent reason is that the fixings have been over tightened and are putting strain on the bearings of the lever, which causes it to become a bind on the external door handles euro lock's surface. It is also possible that the levers haven't been operated at the correct angle, which stretches the latch mechanism and prevents it from fully springing into action.

Another common cause is that the sprung lever is not operating correctly and this is usually due to the sprung not being in the correct position within the backplate. To determine if the handle returns to its horizontal position, simply turn it.

It is crucial to repair any loose door handles immediately. This can cause excessive wear on the screws, and the handle might be able to fall off the base plate. You should also tighten any loose screws on a regular basis to prevent them from becoming looser.

Lever/Snib

These upvc door handles are also known as 'Snib' handle sets and have a snib lever at the top of the lever that can be pressed down to lock your door in the event that you don't have the dummy lock. These door handles are fitted with a Fullex lock 68PZ. (68mm between the spindle and lock centre). We also have a range of other 68PZ door handles from manufacturers like Ferco and Fab & Fix.

The replacement of your door handle is a cost-effective way to update your home, whether replacing handles that are in use or fitting new ones to doors you've built in your house. There are many styles to choose from for upvc door handles, including the classic levers on backplates. Other choices include straight or curved short latches as well as knobs that resemble dummy knobs to lock multi-points. These are great for French doors.

Rose door handles are circular or oval-shaped versions of lever on backplate handles. These door handles are characterized by a lever or a knob that is attached to a backplate. The backplate is removable for hidden fixing.

The handles are available in a variety of finishes, including chrome and coloured finishes, to complement your door and other hardware like knobs, hinges, and bolts. Some handles come with grub screws, which aid in the secure attachment of the lever or knob to the spindle. Some handles are equipped with bathroom spindles that can be used for bathroom locks. They also come with a thumbturn release mechanism and can be used on doors for bathrooms.

Mortise

If your front door's uPVC handle is stuck in the open position, the cause will most likely be with the tubular latch. This can be caused by various reasons but the most prevalent is a lack of lubrication in the latch plate. This can be resolved easily by opening the door and spraying lubricant on the handle and lock. It could also be that the latch is loose from the backplate. This is a more complicated issue that requires the help of the assistance of a specialist.

A multipoint handle is the ideal solution for stuck door handles. These changing window handles are mounted through the faceplate, and are operated with a key or thumb turn knob which activates the cam that locks the deadbolt. The handles are available in a variety of sizes to fit different types of uPVC door, and come in a variety of attractive finishes that complement the hardware that is currently in use. The handles can be bought via the internet or from a local locksmith and can be installed with clear instructions.

To select a replacement handle set, you will be required to know the PZ size of your cylinder. This is the measurement in millimetres that lies between the outer edge of the frame of the door and the centre of the hole for the handle. You will also need the type of lock that is installed on your door, regardless of whether it's a mortise or hook lock. The most effective way to locate the right handles after you have the measurements is to use the brand filter on the website. This will narrow down the options, and you will then choose the appropriate size from there.