• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

• 페이스북 공유
• 트위터 공유
• 

Reasons Your fiat punto key 500 Key Fob Won't Work

A key fob for fiat 500 abarth key 500 makes it easy to open doors and start your vehicle. There are a myriad of reasons why the fob may stop working. This includes a dead coin-battery, water damage, receiver modules issues, and interference.

This listing is for an NEW replacement Fiat Flip Key Remote that appears similar to the Ilco brand. It has to be professionally programmed (click here to search for local automotive locksmiths). Includes trunk, lock and unlock buttons.

Dead Coin Battery

A dead battery is the most common reason for your 500 key fob not working. Modern key fobs have limited operating range and must be within a few inches of the vehicle to work. If you are not within your vehicle, and you press the keyfob button, it will not respond, and display the message "Key Fob Not Detected".

If this occurs, replace the coin-cell battery (Part Number CR2032) by a fresh one of a reliable brand, such as Panasonic Duracell or Energizer. They are usually available at your local hardware store or on the internet.

You can test the battery on your coin-cell by pressing the buttons while you are standing close to your Fiat 500. The parking lights should light up and the key fob should operate the lock and unlock switch.

If the fob's remote doesn't work after replacing the battery, it might be damaged by water that blocks it from communicating with the receiver module in your car. Water damage can occur in a number of ways, from small splashes to submerging the fob salt water at the beach. If you suspect your fob has been exposed to water, try putting it in a dry rice bag to draw the moisture out. If this doesn't work, your fob may require reprogramming by a professional locksmith or dealer.

Water Damage

Water damage can occur if you immerse the fob in the ocean, or wash it in a machine. Saltwater is especially dangerous to the circuit board of the fob that can cause it to short out and eventually end up dying. In the event that you let your fob get wet, it's not an option but if you drop it in a cup of water or fail to take it out of your pants pocket prior to running the washer do not give up hope.

First, remove the battery. Clean the electronic chip using isopropyl or a similar product and then dry it thoroughly before replacing the battery. Then test the fob to check if it functions. If the fob doesn't work, it may have to be reset. This is usually handled by an auto locksmith or dealer.

If your key is a bit older and is not programmed for your vehicle it is necessary to replace it completely. A professional automotive locksmith can complete this simple process. The locksmith will require the key cut to match your car's ignition. The locksmith will also have to reprogram your fob into the car's system. This is a low-cost and fast process that can be completed on the same day.

Receiver Module Issues

One of the most common reasons why your 500 key fob could stop working is that it's simply out of range. The remote has a range of 30 feet, so should you be too far from your car it won't respond to your commands. It is possible to remedy this by moving your remote closer to your vehicle until it responds.

If you've replaced the battery in your coin (commonly known as"button" or "button" or "watch") and the fob isn't working It could be because of an internal circuit board problem. In most cases, reprogramming the fob will solve the issue. You can find the instructions on how to do this for the majority of automobiles by searching YouTube or checking out the owner's manual.

You may have to replace the metal retaining clips that keep the battery of your coin in place. If they loose tension, it could prevent your coin battery from sitting properly and cause your remote to malfunction.

In rare cases the fob might become disconnected from your vehicle due to software problems or hardware issues. This could cause a significant problem, but you can usually fix it by visiting an auto locksmith to have them reprogram your fob. In some instances it is possible that the software will require reinstallation to your body control modules.

Interference

Interference can also cause the key fob to not be able to receive or transmit the signal. This may happen if the keyfob's location is in close proximity to a radio transmitter, like a cellphone or radar detector. Other reasons the key fob might not work include a weak connection to the buttons or the internal chip or water damage.

If your key fob suddenly stopped working, or if you have tried everything at home to resolve it (e.g. You may have a faulty 500 receiver module If you've tried replacing it with a battery, reprogramming or using a spare Key Fiat 500 (pediascape.science) fob. The receiver module, located beneath the dashboard, receives radio frequency signals from your key fob. It converts the signals into electronic commands that are then interpreted by the vehicle.

There is a straightforward method to reset the 500's internal system including the keyfob. Disconnect the battery for 15 minutes, removing first the negative cable, then the positive cable. Then reconnect the battery. This will clear out any residual electricity and restart the car's computers. This can help you get your key fob working again. If the issue continues it is recommended that you consult an expert certified technician. They will be able to identify the exact cause of problems.