• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

• 페이스북 공유
• 트위터 공유
• 

How a Wood Burning Stove Works

Wood burning stoves can be a lovely addition to any home. They should only be used with wood that has been properly seasoned.

Older stoves without secondary combustion let air in between and above the fuel, resulting in the loss of energy, chimney tarring and atmospheric pollution.

Modern wood stoves use a superior combustion method that separates the air supply into two phases. This lets them achieve higher heating efficiencies with lower emissions.

Efficient Combustion

The efficiency of the combustion of a wood stove is a measure of how well the wood you use is turned into heat. It is distinct from heating transfer efficiency, which is the amount of heat that is transferred from your stove into the room. A wood-burning stove with high combustion and heating transfer efficiencies will require less fuel and create less waste, like carbon monoxide, ash, 913875 and steam.

Modern wood stoves typically feature high combustion efficiency, as they have sophisticated design features which allow them to maximize the burning and use less wood. They also tend to have low emissions particularly when using EPA certified stoves, which require a special catalytic combustor that cleans exhaust gases as they leave the stove. These cleaner stoves are an ideal choice for homeowners who want to minimize their environmental impact while still enjoying the warmth of wood stoves.

Increasing the efficiency of your wood stove is a matter of correct operation and maintenance. The most important aspect is to ensure that the combustion process is controlled. This can be achieved by maintaining a fire in the stove by regular additions of small pieces of wood at regular intervals. This will prevent the accumulation of flammable Creosote in the chimney, which could make the stove less efficient.

Another important factor in the efficiency of wood stoves is the use of properly dried and seasoned firewood with an average moisture content of less than 20%. Dry, seasoned firewood will not only produce more heat from the same fuel, but will also cause less smoke and air pollution.

The Environmental Protection Agency (EPA) has established guidelines to limit the amount of smoke and other pollutants that a new stove can emit within an hour. To comply with the EPA guidelines, most modern wood stoves rely on a secondary combustion process or catalytic combustor in order to control combustion and minimize the amount of pollutants they emit. If you're looking to purchase an wood-burning stove that meets EPA emission standards, search for one that has an EPA certification sticker. It must also have a smoke emission level below 4 grams per hr.

Catalytic Combustion

Catalytic woodstoves utilize a honeycomb combustor Www.913875.xyz made of ceramic that is coated with noble metals like palladium or platin. The combustor functions in like the catalyst in your car works to clean the exhaust. The noble metals found in the combustor react to particles and chemicals that are in the smoke, breaking them down into harmless end products like carbon dioxide and water.

This enables the stove to achieve lower emissions and burn cleaner than non-catalytic models without loss of heat output or efficiency. The combustor performs its best when the temperature of gas in the flue is 1,000degF or more. The combustor will not work properly if the flame is burned in a low flame.

Burning foreign substances, such as paper logs, painted or treated wood, can damage the combustor. The burning of these materials can cause "masking" which covers the combustor's cells with a substance, preventing it from functioning effectively. Masking may also result from closing the bypass damper to quickly or refueling using wet wood. If the combustor cells are not regularly cleaned of creosote fly-ash and tar, plugging could occur, which can cause smoke to leak out.

When properly operated and placed, the combustor www.913875.Xyz can provide years of reliable performance. It will require little maintenance, other than cleaning off the soot from its surface after a prolonged burn and then dusting it with a soft, dry brush.

The combustor is equipped with an bypass damper that is open to start the fire, 913875.Xyz and then shut to load the stove. Inspect the bypass for the "operate catalyst" indicator, which will indicate the combustor is operating within its ideal temperature range. Opening the bypass damper too quickly will reduce the operating range of the combustor. Closing the bypass damper too quickly will decrease the temperature at which the inlet is pumped to the combustor and may damage it. Refer to the manual for your stove's instructions on how to operate the damper. You can also reach our customer service department should you need assistance.

Control of Airflow

The controls for air flow in your wood stove are vital to ensuring that the fire burns properly and safely. The primary, secondary, and tertiary systems all work together to ensure that your fire burns efficiently. Each plays a unique part in the combustion process.

The air control is situated beneath or inside the stove door. It controls the amount air that gets into the firebox. More air means a more efficient burning fire, but it also increases the chance of creosote or chimney smokiness buildup. When lighting your wood stove, the primary air control should ideally be open wide and for a short time.

When your fire has accumulated enough heat, the primary air control can be closed down slowly until you're satisfied with the amount of heat produced. The stove or chimney should not emit any smoke as this could indicate the combustion is not efficient.

Secondary airflow controls supply oxygen into the top of your stove, usually in the form of air jets that are placed above your fire. This is the most crucial aspect of controlling your flame. Your fire will be burning too quickly and 913875.xyz produce large amounts of smoke without it.

Tertiary airflow is the last stage of the stove's airflow system. It is carried into the updraft area or chimney. This creates a strong draft inside the flue, allowing your fire to function optimally.

It is crucial to keep in mind that your wood stove was specifically designed and optimized for the purpose of burning wood for fire. Other combustibles may not burn in your wood stove, 913875 leading to high levels of emissions, and even chimney fires. The best kind of fuel to use is well-seasoned hardwood that has been dried for at minimum six months, but softwood can be used as well. Avoid using manmade combustibles like cardboard and paper, as these can cause toxic fumes and build ups of creosote or ash within your stove. It is also a good idea to avoid placing any firewood or other combustibles on top of your fire in case this causes them to explode.

Safety

Wood-burning stoves are an affordable alternative to heating, especially if you live in an area that experiences frequent power outages. However, they can also be dangerous if used improperly. They can produce harmful chemical substances that could cause harm to your health. They may also create a fire hazard as well as carbon monoxide poisoning. You can stay clear of these risks by implementing a few basic safety measures.

Use only dry, clean wood for your stove. Never use gasoline, kerosene or charcoal starter fluid to ignite or ignite fires. Never burn treated wood painted wood, wet wood. Keep the flue open to allow plenty of oxygen in. Add wood in small amounts and do not let the fire go out of control. Do not use a fireplace indoors if you're in a smoke control area.

Make sure that your stove and chimney are installed correctly. Poorly installed wood stoves could cause a fire to the chimney, which can release harmful gasses into your home. Cleaning and inspecting the chimney is also essential. Check that the flue isn't leaky, which could cause carbon monoxide poisoning.

It is a good idea to store your wood in a shed or a tarp. This will allow the wood to season and dry quicker. To minimize the risk of fire, keep the wood from other heat sources. It is recommended to put your stove on a non-flammable surface such as tiles on the floor.

If you have children make sure you supervise them around the stove. They might try to play with the ash hot or even touch the fire, which is dangerous. It is recommended to keep all flammable items at least three feet from the stove. Consider installing a heat-shield to shield walls and surfaces from damage. It's also an excellent idea to have your family practice fire drills at home. This will allow you to escape your home in the case of an emergency. Read our article on fire escape routes to ensure your home secure.