• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

• 페이스북 공유
• 트위터 공유
• 

Ignition Cylinder Lock Repair

The ignition cylinder lock permits the key to be turned and the car to begin. It is controlled by a chamber containing springs which can be damaged by environmental factors like high or low temperatures.

If your ignition switch keys or the switch itself will not turn, it could indicate that the lock cylinder needs to be replaced. It is best to leave this task to a professional automotive locksmith.

Remove the Steering Column Covers

Ignition lock-cylinders are mechanical components that allow a key to be inserted into the ignition switch to be turned to begin an automobile. They can wear out or malfunction in a variety of ways, like keys being put in too hard or in the correct place. They can also break down and fail due to corrosion or any other reason. If your ignition cylinder isn't working it's time to replace it. This is a simple job, but you'll need to remove the cover of the steering column and the airbag cover. The process is risky and could be difficult. It could also require special tools to the replacement cylinder.

The ignition cylinder is located in the middle of the column to which the steering wheel attaches. The clip and two screws at the bottom hold the cylinder in place. It's essential to remove them before you begin working on the cylinder so it doesn't break and get lost.

After the screws are removed, you can take off the plastic retainers that are located at the bottom of the cover. There's a metal retainer that clips into the top of the cover to hold it in the right position. You may need to pry the cover off the steering wheel in order to remove the tabs on the lower part of the plastic.

The tabs can be ripped off by removing one of the retaining screws and bending the tab outward a bit. If the tab is broken off completely, you can replace it with a piece perforated strapping made of metal that is available at many hardware shops. You'll need U-clips for attaching the new "tab" to the bottom. They can be bought at any auto parts shop.

After removing the tabs of plastic and pulling back the airbag cover, it is now possible to reach the ignition cylinder. With the 1/16-inch allen wrench to open the ignition lock and push it onto the cylinder retaining pin. Then, you can pull the cylinder out. It is possible to replace it with an anti-theft cylinder.

Remove the Ignition Cylinder

Although a majority of vehicles now have push-to-start technology, there are some vehicles on the market that require an ignition lock. This mechanical cylinder is housed inside the electrically powered device called the ignition switch. It locks the ignition key replacement and "reads" anti-theft codes inside the car ignition lock key to allow it to start.

It's the right time to contact an auto locksmith if the vehicle is showing signs of a broken lock cylinder. A damaged cylinder can lead to numerous issues, including lack of power from the engine and issues when it comes to inserting and removing the key. Worn keys can damage the wafer tumblers that allow the ignition cylinder to turn and create a blockage which prevents your car from starting.

Based on the make and model, the ignition switch cover may be held on by either a clip or screw. With a screwdriver, loosen the screw, and then remove the cover to reveal the cylinder that locks the ignition. It's usually a metal cylinder, which is about the size of the size of a quarter.

To remove the cylinder, you will need to drill the pin that holds it. Make use of a drill bit that is slightly larger than the slot for the key and drill straight into it until the cylinder snaps free. You'll then be able to pull the cylinder out and replace it with a replacement.

The procedure to remove the ignition cylinder varies by manufacturer, so you'll need to review your service manual to find out the steps to follow. Once you have the cylinder removed, you can install the new ignition switch.

Before you can do that, you'll need to reinstall the covers for the steering column. Also, you'll need to fix two screws on top of the lock assembly to keep it in place. After you've done that installing your new ignition cylinder shouldn't prove to be too difficult.

Take off the Ignition Switch

The ignition cylinder and the switch are separate components of the electrical system inside your car. Although they appear like they do, you can fix or replace them on your own. The switch is the electrical portion that provides power to the vehicle while the cylinder is the mechanical tumbler your key is able to slide into. Generally, you can detect that the mobile ignition lock repair services cylinder is not working properly due to its inability to turn your key.

If the cylinder fails, the pins inside the tumbler can wear out, making it hard or impossible to pull or insert your key. If you notice your key is damaged and won't turn anymore it is recommended to get the wafers replaced or smoothed out by professional locksmiths.

The ignition cylinder is exposed by removing the screw or bolt, depending on the make of your vehicle. Consult your vehicle's manual before attempting this at home. It is a risk and cause damage to the steering column or plastic covers. Furthermore the switch is linked with wiring for airbags, and tampering with this could cause serious injuries.

To remove the ignition coil, you will need to loosen it using the help of a drill. You can also use pliers to disengage it from the assembly, but this is often more difficult than using the screwdriver. Once the ignition cylinder is removed, you can purchase an alternative one at your local auto shop.

After installing the new ignition cylinder, you'll need to reconnect all of the wires to the electrical connection in the steering column, and then test the function. It's usually easier to disconnect the battery, then remove the ignition key, and then start the car. When the ignition is functioning, you can reconnect the battery and try it again. If it's still not starting then you'll need to have the immobilizer system reset by a dealer or automotive service technician. This is a complicated procedure that should be handled by professionals.

Reinstall the Ignition Cylinder

The ignition switch in your vehicle sends out an indication to the engine that it's time to begin. The key is inserted into a lock cylinder to start the process, but the pins and wafers inside the cylinder may wear out over time. It can be difficult or impossible to start your car if the cylinder becomes stuck.

If your key doesn't turn on the ignition, it's likely that it's time to get replaced. A locksmith can replace the cylinder in your ignition with a replacement so that your key will continue to work with your current ignition switch.

To take off the lock to remove the lock, press down on the release pin located at the bottom of your assembly and slide the cylinder from its housing. If the cylinder isn't sliding out, try pushing in on the release pin a second time or using a screwdriver, you can press an anti-rotation small button underneath the cylinder's surface. You may also try pushing in on the cylinder with your key while turning it to the ACC or accessory position to see if you can force it out.

Once you've removed the old cylinder, install your new one and then turn on the vehicle to ensure whether it's functioning. If it is, you can connect the trim pieces you removed to access the cylinder. Then you can perform a relearning procedure to connect the new keys.

Although the lock for the ignition cylinder isn't as integral to the functioning of your car as it used to be but there are still situations where you may need to replace it. Consult a professional such as an locksmith or an automotive dealer to ensure that the task is completed without damaging the steering column's or other parts of your vehicle. It is essential to ensure that the new ignition is properly coded so that your car recognizes it as authentic keys. This will usually require an expert or a dealer to do this process of learning.