• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

• 페이스북 공유
• 트위터 공유
• 

How to Program a Car Key

Modern cars use more than just a key to start the engine. They also have a remote that can lock and unlock doors. Key fobs have to be programmed to work properly.

Certain keys for cars can be programmed by the owner themselves but it's best to consult with an expert. This will help protect against any possible damage to the car's computer system and also ensure that the new key functions correctly.

How to program a Key

Up until the turn of the 21st century, most cars used basic key systems. Keys themselves were metal and had grooves that matched the internal components of the ignition cylinder. As technology advanced, more and more car makers began to combine electronic and physical protocols to stop theft. These key systems are referred to as transponder keys or chip keys and they're designed to make it difficult for thieves to get into the vehicle.

The key chips inside the keys have a unique serial number, which transmits an electronic signal to the receiver in your car. When the signal is received, it compares it to the code that is stored in the car's computer. If the codes match the car will begin to begin. If not, it will not start at all. This is the reason you should keep a spare car key, particularly if your system is based on transponders.

You'll require specialized equipment to be able to program keys. You'll need to buy an uncut key that matches the model and make of your car. You can purchase these at a locksmith or a car dealership, but it's important to purchase the correct keys. If you use a key for another model, it will not function.

To begin the process, simply insert the new key into the ignition and turn it to the "on" position. You will need to leave the new key in this position for approximately 10 minutes and 30 second. After the time has expired you can take off the key and observe if the security light on your dashboard was gone. If it didn't go out you'll have to repeat the process a third time.

This method is only compatible with GM vehicles and isn't foolproof. If you're looking for a more reliable and secure solution go to an auto locksmith or dealer to get your car programmed using an embedded chip. They will have the tools and equipment to connect to the onboard diagnostic port of your car and make the switch.

Keyless Entry Systems

Keyless entry systems give access to properties without the need for a physical credential. They utilize a combination of sensors and an onboard computer to provide security. This allows you to control the system and monitor activities from any location on the property, and eliminates the requirement for locks or keys. The system can also detect stolen or lost cards and disable them. The newest models also allow remote management and configuration and are cloud-based.

Modern automobiles are equipped with keyless entry systems. This system works by emitting radio signals that are detected by the keyfob. The signals are compared with the code stored in the car's computer and, if all is well, the car will unlock. The car will not start when the signals aren't the same. There are a variety of steps you can follow to program your new key fob, if it isn't already programmed.

You'll first need to make sure that all doors excluding the driver's door are locked. You'll also need the original key fob, along with any additional keys you want to program. You can also try the local auto parts store, as they may have the appropriate programming tool for your vehicle. If these steps don't work, you will have to consult the owner's manual or an expert locksmith.

Once you have the right tool You can begin the process of reprogramming a car key your key fob following the instructions of the manufacturer. This procedure is usually quick and easy. For instance, you could be directed to insert your new key into the ignition while keeping the doors shut, and then press a button on the key Fob key Programmer within a brief time frame. The car might respond by cycling door locks or emitting an audible chime as an indication that the key was successfully programmed.

Many locksmiths are equipped with special tools that allow them to bypass the built-in EEPROM security on your car's key fob or remote. This is a risky technique and could cause data corruption on your car's computer. This is best left to a professional, who can lower the chance of data corruption and make sure that your keys are programmed correctly.

Transponder Keys

Transponder keys, also referred to as chip keys, are equipped with a microchip embedded in the head of the key. When the key is inserted into the ignition lock barrel and turned into the ON position the antenna ring transmits an electromagnetic energy blast through the transponder chip. The chip absorbs the energy and then transmits a radio frequency signal which contains an identification number. This code matches the unique digital serial numbers in the computer system of the car. This helps prevent unauthorised attempts to start the car, since only the right key can start the car key programming.

This type of technology is thought to be more secure than a conventional car key since it makes it more difficult for a thief "hot wire" the vehicle and then start it. It's not foolproof and thieves have discovered ways to evade detection and defeat the system. So even cars with transponder key are not safe from theft.

You may be able program a transponder key by yourself with a key programmer compatible with your car. The key programmer will come with a manual that will guide you step-by-step through the process. Follow the steps and switch on the security light on your dashboard prior to starting your engine.

If you're not comfortable the use of a key programmer or if your car has more advanced features like remote head keys or smart keys, you may turn to a professional locksmith assistance. They will have the tools and equipment required to cut an uncut key, erase the old one from the computer of the car, and then program the new key for it to work correctly. This will save your time and money, and will ensure that your car's security system working exactly as it should. Plus, it's a lot more secure than doing it yourself! Using the wrong key programmers or following unofficial guides can corrupt the information in the car's system, and result in the key not working.

Remotes

If your car keys aren't working it could be necessary to change the programming. It's a straightforward process for the majority of modern cars which use keyfobs. Some models are more complex and require a special programming device, which is usually available from the dealer or through auto locksmiths.

Fortunately, most modern car manufacturers have made their key systems more secure to reduce vehicle thefts. The key system is designed to stop hot-wiring (the method of using a key from another vehicle to start the engine) and other similar methods. Therefore, you'll need at least two functioning key fobs for your vehicle in order to ensure that the process works. It's essential to have two spare keys on hand.

The key fobs contain electronic chips that transmit radio signals to the car's receiver. The computer examines the code of the key with the database. If the codes match the car will begin. If not, the vehicle will be dead or refuses to start. The majority of these electronic keys can be programmed and replaced by a professional locksmith or dealer in the field with the appropriate equipment.

If you're able to find an inexpensive car key programmer on the internet or in an auto parts store, the procedure should be fairly straightforward. You'll have to follow a set of steps that include inserting the ignition keys programmed, turning it on without actually starting the vehicle, then shutting off the key. You will need to repeat the steps a specific number of times within a specified time frame to get your vehicle into programming mode. The door locks will turn on and off or chime.

Some modern cars can only be programmed by means of a device that is connected to the onboard diagnostics port or an EEPROM programming procedure. These tools are costly and are therefore not affordable for most car owners. As such, most experts in the field recommend that you consult with an experienced auto dealer or locksmith to program your keys.