• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

• 페이스북 공유
• 트위터 공유
• 

Why is My Car Ignition Locked?

There are many reasons why your car ignition may be locked. One reason is that the key is dirty or has a damaged wafer inside it. It is possible to fix this by sliding the key in and out of the cylinder several times.

Another possibility is that the pins in the lock cylinder have become stuck. You can use a small tack hammer to gently tap the cylinder to loosen them.

Check the Battery

If the car is in Park or neutral, but won't turn on when you insert the key into the ignition, there may be an issue with the shifter switch for the transmission. This can be easily solved by moving the switch up or down to put the car ignition key replacement in gear.

If the car is still unable to turn, the issue could be related to the neutral safety cable or transmission shifter. A mechanic or an auto ignition key replacement locksmith can easily fix these issues.

It's also possible that the ignition lock repair near me cylinder is worn out. Over time, the ignition and the key can wear out, which causes them to become difficult to remove or insert. A lubricant, such as silicon lock grease could solve this problem, allowing the wafers to slide into place.

The filth from your pockets and adhesive from tapes that hold packages together can also build up on the key, preventing it from sliding into the ignition. You can clean the key with a cloth, or a cleaner, such as Triflow to fix this issue. You can also test a spare key to determine if the problem is the key or ignition.

When the key is in the ignition you can tap it with a the hammer with a small amount. This can cause a small vibration that could be enough to loosen the wafers within the ignition which will allow them to slide in place. However, you must be cautious not to damage the ignition key or cylinder.

If none of the above work, you should call a locksmith to check it out. The key may be damaged inside the ignition cylinder, or it might be time to replace it altogether. Locksmiths can create a replacement key if the problem is with the key. If the cylinder in the ignition is the cause then you'll have to take the car ignition key replacement to a repair shop in order for it to be repaired. Luckily, these issues are usually very easy to repair.

Examine the Steering Wheel

A steering wheel that is locked may cause the ignition to stop turning. It can happen when a driver accidentally engages the steering wheel while they exit or get into the vehicle. This usually happens by yanking the wheel and being able to hold it against their body. It can also happen when an individual in the back seat is unable to stop it when they climb out of the car.

Luckily it's a simple fix and does not require a trip to locksmiths or mechanics. First, make sure that the gear shift is either in neutral or Park. If it's not you can gently pull or push the gear shifter until it shifts to one of these positions. You should also activate the handbrake or press the brake before turning the key.

If the wheel is not locked, a quick inspection of the steering column should confirm that the key is connected to the lock cylinder. A small "Lock label is typically found in the lower portion the ignition circle. It is easily removed by gently jiggling the key or pulling it down with moderate force. It is important to not apply too much pressure, as it could damage the key, or damage a wafer inside the lock cylinder.

A spare key can be used to deactivate the lock. This could indicate that the original key has worn out and no capable of engaging the wafers in the lock cylinder. If this is the case then a professional at Karl Chevrolet Webster City will be able to make a replacement key.

If the key still doesn't engage after spraying the penetrating lubricant it may aid. Apply a small amount of penetrating oil around the keyhole and ignition. Then, jiggle it or tap it lightly to make sure it is working. If this isn't working, you'll likely need to see an expert at your local auto dealer. They will be able to provide you with a new key, and will also replace the ignition cylinder in the event that it is required.

Check the Key

It could be that your key has been damaged if it does not turn on. You can try removing any foreign material from the key (lint or adhesive from packing tape, etc.). You should also try rubbing alcohol or Goo Gone on the key to see if it aids.

It is possible that the lock pins inside aren't moving correctly when you insert the key. You can test an extra key by gently pulling it out of the ignition after you put it in. This should let you feel and hear if the internal lock pins move as they should. If you don't hear or feel any movement, you could grease them with graphite. You can buy graphite in small tubes which can be sprinkled into the keyhole. This will allow the pins to slide into position when you insert the key and stop them from becoming stuck.

It could be that your key has become worn out or damaged and isn't able to work with the pins inside the ignition cylinder. This could cause the cylinder to stop to turn, which can prevent you from starting your vehicle. If this happens you'll need take your vehicle to an auto locksmith ignition replacement locksmith or repair shop for repair.

If you are able to turn your car with a spare key, and you've eliminated any issues with the steering wheel or battery it could be because the ignition cylinder has worn out. You can attempt to loosen the lock cylinder using the sharp end of a screwdriver or the handle of a Hammer (not the head). Often, tapping gently on the cylinder can free it to allow you to turn the key of your car. If this doesn't work then you'll need to replace the lock cylinder by a mechanic.

Check the Ignition Socket

The ignition socket is the place where your key slides in and out when you insert it. Most of the time, it gets filled with debris or is due to wear and tear. You can inject some silicon lock lubricant into the ignition.

You can also use a small hammer to gently tap the interior of the cylinder for ignition, in an attempt to loosen or reset the pins that could be out of alignment. Be very careful to not overdo it or you may cause severe damage to the ignition switch.

It is important to check that your car's gearbox is set to park or neutral before you attempt this. Many newer cars have an option to lock the steering wheel when it is not in park or neutral, which can prevent the key from being turned in the ignition.

If you have tried all of these steps and your key still won't turn, it is possible that the ignition housing needs to be replaced. It is important to know that different vehicles require different procedures for replacing the ignition cylinder.

This typically involves removing the plastic covering that covers the steering column and ignition assembly. To remove this, you will need to first adjust the tilt-wheel to the lowest setting and then remove any fasteners that hold it in place.

After removing the cover, you'll have to remove the old ignition cylinder from the steering column. It is then essential to check the new one you purchased with the original one to ensure that they are an identical match. Once this is done, the new ignition cylinder can be installed in the same way that the old one was removed.

It is possible that, despite our best efforts, the ignition may become damaged and need to be replaced. It is recommended that if this happens, you call an Tempe Locksmith. A locksmith will be able to help you select the proper replacement and then install it correctly to ensure that your vehicle can be started again.