• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

• 페이스북 공유
• 트위터 공유
• 

Glass Window Repair

Professional window repairmen work high above the ground, moving massive glass panes. They adhere to strict safety standards and often work under extreme weather conditions.

Wearing protective clothing, take off the metal glazing points as well as all glazing putty with an utility knife. A heat gun may help soften the old putty and make it easier to remove.

Replacement

When a window's pane breaks, it can be tempting to try and repair the glass instead of replace it. However, replacing windows is typically more cost-effective, and can also assist in preventing other issues in your home's energy efficiency. You should also consider the type of glass that is broken to determine if it is an interim fix or if you will need to invest in a more permanent solution.

To fix a damaged window, take off the frame or sash and place it on the work surface. Wearing eye protection, gently wiggle the window's frame and pull out any remaining shards. Use a utility blade to remove the glazing compound, as well as the glazing points that hold the window in place. Keep track of the components and their locations so they can be reinstalled.

Once the frame and sash are removed, you can begin preparing to install new glass. Before you begin make sure that the opening in the frame is sized for your replacement window. To allow for expansion and contraction of the glass and frame and contraction take measurements in both directions across the opening and subtract 1/8 inch. After that, you can purchase double-strength glasses cut to these exact measurements. It is a good idea to also purchase enough glazier's clips or points to place them every 6 inches around each window pane.

If the manufacturer is responsible for this then you should call them and submit an claim. After the new glass has been installed, it is important to cover it with a thin layer glaziers compound. After drying the compound, you can paint it to match the frame of the window.

If you have a crack that extends more than an inch, scoring an arc of a razor blade that is just above the crack will help stop it from spreading further. This method isn't completely foolproof, but it could slow the development of the crack down to a manageable level until you can take permanent measures.

Repair

Professional window contractors are trained to handle various kinds of glass, and they have the tools to do a proper job. They also understand the best methods for disposing of waste, and are less likely to leave crumbs behind, which could potentially injure family members or pets. They're also familiar with different window types and may be capable of identifying issues that aren't apparent to the uninitiated homeowner.

Wear safety goggles and gloves prior to beginning the process of repairing cracked glass. Even a small break can cause shards to fly, which could pose a risk to anyone living in or around the home. It's also crucial to figure out what caused the crack in the first place, as it could help avoid future issues.

Start by making an epoxy mix that is two-part. They are usually made up of a 50/50 mix of resin and hardener and must be mixed quickly. After the mixture is made, apply it directly to the crack and allow it to dry. It will take just some minutes, but you must be quick as the mixture is thick and drys very quickly.

After the epoxy has dried, you can take off any excess using a putty knife. You'll need to clean the cracks in the glass. If you don't do this correctly, the residue could cause further damage to the glass. After the glass has been cleaned, use a putty knife to smooth the compound along the edge of the window and to match it with the frame made of wood.

To make a more durable option, consider using a plastic cover. A trash bag that is heavy-duty or tarp is ideal, however you can also use masking tape to cover the glass. This will stop the crack from spreading and will also keep wind, water and bugs out.

If you're not able to reach the window in a timely manner and you're not able to get there quickly, you can use silicone sealant to make temporary repairs. Apply a small amount of silicone sealant around the edge of the broken glass. It won't completely fill the gap between the frame and glass, but it will keep the break in place while you repair it.

Repainting

If your windows with glass are old, you may need to paint them. This is an affordable alternative to window replacement and can give your home a fresh new look. Make sure the window is clean prior to painting. Use rubbing alcohol or soap and water to get rid of oil smudges, as well as other traces of dirt that can hinder paint from adhering. Wear rubber gloves when working on glass surfaces to prevent the transfer of oils from your hands onto the glass. In the end, you should apply several thin coats of paint instead of one thick layer. This will make the paint last longer, and will keep your windows looking smooth and even.

If you're planning to repaint your glass windows, make sure you have the appropriate tools nearby. You'll require a brush or sponge, painter's adhesive, a ruler, toothpicks, and a few other tools, such as paper towels or a rag. You should also have the brushes and paint you'll use to complete the project. Follow the manufacturer's directions. Have patience as it can take a while for the paint to completely dry.

If you are using solvent-based paint, also ensure that the room where you work is adequately ventilated. This will reduce the risk of breathing toxic chemicals, and the paint will dry faster. It is also important to ensure you have a protective mask for any spray paints you apply.

For older glass windows, it is necessary to prepare the surface before painting. Use warm water and soap to thoroughly clean the glass window. Then, rub alcohol on any grease or oil residues that might hinder the adhesion of the paint. Make sure that the windows are dry before you begin to paint them.

If you have energy efficient double pane windows on your windows, it could be possible to make claims for repair or replacement with the company that makes the windows or the dealer who sold them. This is especially the case if you've experienced numerous issues with broken glass or condensation even though the windows are covered under warranty.

Sealing

Whether you have old double glazed window repairs near me-pane windows with a damaged seal or more recent insulated glass units (IGUs) that have experienced defogging and fogging, there are a variety of options to address the issue. It is the most expensive option to replace both the insulation unit and the frame. However, it may be required in situations where fog or condensation is creating energy losses. Other options include replacing the IGU with a single pane or repair it by drilling a small hole through the bottom of the unit, and then filling the solution with anti-fog.

You can also close the gap between a window frame and a threshold or sill by using a felt strip, or vinyl V-strip. Felt is cheap and can be fixed by gluing, nailing, or stapled into place, but it does not offer much protection against moisture. Vinyl v-strips are simple to put up and is durable, but can be expensive. It is generally reserved for areas that are subjected to high abrasion. Door sweeps are easy to nail in place and are cheap. However, they provide little or no protection between the threshold and air.

To repair a damaged window seal make use of a putty blade to remove the old caulk. Wearing eye protection and gloves take out the glazing point -- small fasteners with sharp, pointed tips that pin the glass into the frame's recess. After removing the glazing points, remove the grooves, then sand the wood. Wipe off any sanding debris then seal the wood surface using a linseed oil-based paint or clear sealer.

A putty or caulking knife can be used to apply traditional glazing putty, however the use of a knife allows for a more precise application, and a more secure seal. Choose a putty that is specifically designed for glass as it is more durable and will adhere better.

Apply a thin layer of glue across the inside of the frame where it joins the glass. Slide the window into the frame so that the drawn line on the glass aligns with the frame's edge. Apply pressure on the glass to compress the putty and glass into an elongated seal. Smooth the compound with a gloved hand and remove any drips or caulk that were not applied correctly before it has dried.