• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

• 페이스북 공유
• 트위터 공유
• 

UPVC Replacement Door Handles

The handles on your doors are worn out over time and will need to be replaced. It is crucial to keep the same dimensions as the handles that were previously used when replacing them.

The top screw position, the lever and the keyhole dimensions are the three measurements you need to check. Use the size guide to assist you.

Inline Lever/Lever

A lever handle is a modern door handle designed to work with new or replacement doors. This type of handle is available in a variety of styles and finishes. This handle is offered by several manufacturers including Avocet ERA Fullex Hoppe Mila Millenco Yale.

Fab and Fix Windsor Inline Sprung Lever Door Handle

The uPVC/Composite door handles are made of robust materials and are suitable for doors with multi-point locks that require a strong design. The handles are inline, and they use the same screws and spindle to secure them. They can be easily mounted on any uPVC/Composite door.

The sprung lever design allows the window handle upvc to be set and angled to provide a comfortable grip and is suitable for all users. The handle has been tested to 200,000 cycles. This helps to ensure the quality of the finish and the performance of the handle over time. The sprung lever can also be shortened to fit more locks. This is particularly beneficial for narrower door frames in which the cylinder is further back. A shorter lever is an ideal choice for doors where the latch can be opened by a thumb turn on the inside.

Lever Pad

The lever pad upvc handle is different from the lever handles for internal bifold doors found on most doors. The handle can operate from a single spindle (inline) or independently from each side by using two inline or offset spindles (pad). They are typically utilized on UPVC doors with double glazing handle glazing. They come in a variety of finishes and variations.

The handles are available in a variety of finishes, including White Chrome and Gold. The finish meets BS EN 1670:2007 Grade 5 and is also resistant to corrosion, thereby giving the handle a high degree of durability and performance for the intended use.

All UPVC lever pads for handles come with a spindle, screws, and can be fitted on the uPVC door. The 211mm backplate fixation centres permit a larger handle, which is typically beneficial when replacing a damaged or old multi-point door lock mechanism. The handle levers are sprung, solving the problem of handles hanging out of their horizontal position when not in use.

When choosing a replacement handles for windows UPVC handle and spindle it is crucial to match the dimensions of the PZ of both the multipoint lock and the uPVC door handle replacements. This measurement is often known as the handle centre or 'cylinder centres and is an essential aspect to match the appropriate handles.

Once you have the correct PZ size you will then be required to make sure that the lever pads and push pads are of a suitable shape to fit the American with Disabilities Act (ADA) compatible handles you require for your doors. These are typically rectangular or round in design with an internal lever and an external push pad.

The majority of UPVC lever pads we offer are sprung, which means that they will return to their horizontal position when not in use, rather than hanging out and possibly securing in the frame. This prevents draughts from entering the building. The majority of UPVC lever pad handles come in both left and right handed models which allows them to be placed on either side of doors.

Euro Cylinder

Cylinder locks are usually found on uPVC doors, but can be utilized on other types of door. The cylinder lock is operated by a key which unlocks the cylinder case. This reveals pins that can be aligned to those inside the lock, and permit them to turn the revolving camera, opening the door. Euro cylinders can be fitted with up to six pins. Doors that are internal and external require different levels of security.

The selection of a cylinder is crucial. It's dependent on the use that your doors and handles will receive. Doors that are external, for instance should be equipped with higher security cylinders, whereas internal doors can be secured with a standard cylinder. Additionally, certain cylinders come with additional features that can improve security, for instance anti-drill and anti-bump characteristics.

A euro cylinder must be measured accurately to ensure that it is the correct size for your door. The cylinder should be measured from the hole for fixing screws in the middle to each end of the cylinder including the thumb turn if you have one. It is best to do this with the lock in place however, when this isn't possible, you may remove it to take measurements. A cylinder that protrudes beyond the handle and escutcheon could be susceptible to attacks like snapping locks, therefore it is important to make sure it's not too long.

The design of the latest cylinders comes with anti-drilling as well as bump resistance features. They are designed to decrease the chance of a attack by causing the cylinder to rotate in the opposite direction. This can help to deflect attacks and protect your door.

Some cylinders are designed to withstand snapping. This is a more frequent method of attack on cylinders where the break line inside the lock is smashed by a tool that is specially designed to break the front of the cylinder to allow the door to be opened. This is a much faster and simpler method to gain access than through the use of a multipoint locking system. It also leaves no evidence of the break-in which can delay insurance claims.

Spring Cassette

This spring cassette sits inside the base of the door handle backplate providing a sprung solution that returns your multipoint lock handles to their rest position after use. There was a time when handles of this kind didn't have a spring built into them, and without it they are more likely to slide or drop once the locking mechanism is removed. This simple feature is one of the best ways to correct this, and is an excellent way to stop your upvc doors from getting stuck in either closed or open position, as they aren't always simple to close manually.

These spring cassettes have been specifically designed to be used with multipoint locks sprung but they won't work with multipoint handles that are not sprung and you will require a hole specifically cut in your backplate in order for them to fit (please look at the image for a technical diagram). These cassettes are a replacement to damaged or missing cassettes that are in the backplate of uPVC door handles. They are sold as a single unit. They feature a square cut out that is able to accommodate an 8mm shaft.

These spring cassettes are a fantastic cost-effective solution to the issue of handles on your doors sagging. These spring cassettes are easy to install and can extend the lifespan of your uPVC door. Please contact our team for more information about our selection of uPVC accessories and spares. We are always happy to provide expert advice and support you.