• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

• 페이스북 공유
• 트위터 공유
• 

Glass Window Repair

Professional window repairmen can maneuver large panes of tempered glass from a height higher than the ground. They work in extreme conditions and follow strict safety protocols.

Wearing protective clothing, take off the metal glazing points as well as all glazing putty using an utility knife. A heat gun can help to soften and take off the old putty.

Replacement

It is tempting to repair the window glass instead of replacing it when panes break. However, replacing windows is typically more cost-effective, and can also help prevent other problems with your home's energy efficiency. It is also important to consider the kind of glass that is damaged to determine if it is a temporary fix or if you will require a more permanent solution.

The first step in fixing broken windows is to take off the sash, also known as the frame and place it flat on a table. While wearing eye protection, gently wiggle and pull out any remaining shards within the window. Utilize a utility knife to cut off the glazing compound and the glazing points that hold the window in place. Keep the track of these components and their locations to ensure that they can be reinstalled later.

After removing the frame and sash you can begin preparing to replace the glass. Be sure to check that the opening of the frame is the right size for your replacement window. Take measurements both ways across the opening, and then subtract 1/8 inch from each measurement to give the expansion and contraction of the frame and glass. Then, purchase double glazed window repairs near me-strength glass that are cut to these exact dimensions. It is recommended also to purchase enough glazier's clips or points to place them every 6 inches around each window pane.

If the manufacturer is responsible for this then you should call them and make a claim. Once the new glass is installed, installer it needs to be covered with a thin coating of the compound used by glaziers. After the compound has dried then you can paint it to match the frame of the window.

If you have a crack that extends more than an inch, cutting a small arc with the edge of a blade just over the crack will help prevent it from spreading any further. This method isn't foolproof, but it will slow down the progression of the cracked until you can take more permanent measures.

Repair

Professional window installers know how to handle a variety of glass, and they have the tools necessary to do an excellent job. They are able to dispose of waste in a safe manner which means they are less likely than others to leave behind scraps that could harm family pets or family members. They're also used to working with different window types and are aware of issues that might not be apparent to a homeowner who isn't experienced.

Before you begin the process of repairing cracked window glass, be sure to wear safety goggles and gloves. Even a small break can cause shards to fly, creating a risk for anyone living in or around the home. It's important to determine what caused the crack, so that you can prevent future problems.

Make a two-part mixture of epoxy. These are usually 50/50 mixture of hardener and resin and they must be quickly mixed. After the mix has been prepared and applied, simply apply it to the crack and allow it to dry. It should take only about a few minutes, but it is important to be quick because the mixture is extremely thick and drys very quickly.

Once the epoxy is dried, you can take off any excess with a putty knife. You'll then need to clean the cracks in the glass. If you don't do it properly, the residue can cause further damage to the glass. Once the glass is cleaned with a putty blade, use it to smooth the compound along the edges of the window, and then align it with the frame of wood.

For a more durable solution you can consider using a plastic covering. You can cover the glass with masking tape or a sturdy trashbag. This will stop the crack from spreading, and will also keep wind, water and insects out.

You can create an interim fix when you are unable access the window in an efficient manner. Apply a small amount silicone sealant around the edge of the damaged glass. It won't close the gap between the frame and the glass completely, but it will hold the broken piece in place until you are able to repair it.

Repainting

If your windows with glass are old, you may want to repaint them. This is an affordable alternative to replacing windows and will give your home a fresh new appearance. Make sure the surface is clean before painting. Wash the window with water and soap or ruby alcohol to eliminate oil smudges and other traces that can prevent the paint from adhering. Wear rubber gloves while working on glass to avoid transferring your own oils onto the surface of the window. Apply multiple thin coats instead of just one large coat. This will allow the paint to last longer and keep your windows looking smooth and even.

Make sure you have the proper tools available in case you want to paint glass windows. You'll need a brush, sponge, painter's tape, a ruler, toothpicks, as well as a few other tools such as a rag or paper towel. It is recommended to have the paints and brushes that you will be using on hand. Be sure to adhere to the manufacturer's guidelines and have a good amount of patience as it can take a while for the paint to dry.

If you're using solvent-based paints, you must also ensure that the room where you work is well ventilated. This will help to reduce the chance of inhaling toxic chemicals, and also the paint will dry quicker. Use a mask that is protective when using spray paints.

You'll need to wash the glass window thoroughly with soap and warm water before you paint it. Clean the glass thoroughly with soap and warm water. You can then use rubbing alcohol to clean off any oil or grease that could affect the adhesion of the paint. Make sure that the windows are completely dry before you begin painting them.

If your glass windows are energy efficient dual pane windows, you may be able to make a claim with the window manufacturer or dealer that sold them to cover any repair or replacement costs. This is especially relevant if you've had numerous issues with broken glass or condensation and the windows are covered under warranty.

Sealing

If you have double-pane windows with a damaged seal or more recent insulated glass units (IGUs) that have experienced fogging and fogging, there are a variety of options to address the issue. The most costly option is to replace the insulated unit and frame but it may be required if fog or condensation are causing energy loss. Other options include replacing the IGU with a single pane, or fixing the IGU that is in place by drilling a hole through the bottom and filling it with an anti-fogging agent.

You can also close the gap between the window frame and the threshold or sill by using a felt strip, vinyl v-strips, or a door sweep. Felt can be stapled, glued or nailed into place but doesn't offer much protection against moisture. Vinyl v-strip is easy to put up and is durable, but can be expensive. It is usually used in areas that are subject to high abrasion. Door sweeps are inexpensive and can be nailed to the floor however they provide very little or no protection between the threshold or sill and dust, air, and other debris.

To fix a damaged window seal using a putty knife, you need to scrape off the caulk. Wearing protective eyewear and gloves carefully remove the glazing points -- small fasteners that fix the glass into the frame's recess with sharp, pointed edges. After taking out the glazing points, remove the grooves and sand the wood. Clean any sanding dust, then seal the bare wood surface using a linseed oil-based paint or clear sealer.

A caulking knife or putty can be used to apply the traditional glazing putty, but the use of a knife allows for a more precise application, and a more secure seal. Make sure you choose a putty specifically designed for glass windows as it will be more adhesive and a longer life.

Apply a thin bead of the putty to the inside edge of the frame where it touches the glass. Slide the window into the frame so that scribed line on the glass is aligned with the frame's edge. Apply pressure on the glass to compress the putty into a tight seal. Smooth the compound with gloves and get rid of any caulk or drips that were not applied correctly before it dries.