• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

• 페이스북 공유
• 트위터 공유
• 

How to Fix a Loose Door Hinge

Most homeowners can repair a loose hinge. If the holes for screws are shattered and do not hold screws, you could need to use dowels and wood glue to fix the hinge.

Before you do that though scrub away any surface rust. This will allow the dowels to stay in place and give them a solid foundation to hold onto.

Eliminating the Hinges

A lot of door hinges can be removed, which makes it easier to move the door from one side to another or to remove the entire door off of the frame should it be needed. Removing the hinges is fairly simple for anyone with patience, though you do have to know how to do it right.

If the hinges have been painted it is necessary to remove it prior to trying to remove the pins. If you don't, the paint could peel off and scratch your door when you attempt to lift it. To break the paint seal put the hinges into an stainless steel pan and fill the pan with water until the hinges are fully submerged. Allow the hinges to sit in the pan for about 30 minutes. The heat from the water will soften the paint and make it easier to take off the pins.

Once the pins are loosened, you can remove the hinges from the frame and door. It is possible to use a standard screwdriver, but it is recommended to use a magnetic screwdriver for this task. This type of screwdriver has been specifically designed to grab metal screws and aid you in getting the job accomplished much faster.

Before you attempt to remove the hinges it is recommended to spray them with a lubricant. A simple lubricant will help the process go by more quickly and help you remove the screws and pins. You can find this type of lubricant in most hardware and home improvement stores.

It is important to keep in mind that the number of door hinges you'll require will vary depending on the type of door and the settings. Doors with a heavier core and solid-core will require more hinges, while lighter-weight and hollow-core doors might only require two or three.

Understanding the various types of hinges will help determine which one is best for your particular situation. Exterior hinges are typically designed to support the door's weight and interior hinges have to be able to support lighter loads.

Reattaching the Hinges

Sometimes a door hinge will become looser over time and begin to hang crookedly or slide. This can cause problems however, it's usually simple to repair. Most of the time, a simple retightening of the screw will fix the problem. However in the event that the screw holes are ripped out, it can be more difficult to do. A wood dowel can be used to tighten these holes again.

Begin by drilling out the hole from the previous one using a drill bit that is similar to the size of the new screw (typically 3/8"). Fill in the hole using wood glue and a wooden stick. To ensure a tight fit, the dowel should be cut to the same length as the screw. After that, reinstall the screw and tighten it to the desired level of tightness. If the door has an tendency to get stuck and close, then you can add another dowel to the gap and repeat the process. Close the door slowly after each adjustment to make sure that the clearances around the perimeter are correct.

You could also use a wood plug in place of the dowel. It works similarly, but it may take a bit longer to install. Simply whittle a chunk of wood to the proper size to ensure a secure fit, and then insert it into the hole. If you don't have an instrument for woodworking You can use toothpicks or matchsticks made from wood.

Make use of a countersink in order to make the hole smaller for the head of screw after you have reinstalled it. This will stop the screw from hitting the edges of the doors when they are closed and opened. This will make it easier to tighten the screws after replacing hinges.

After you have reinstalled the hinge, be sure to lubricate it with a dry lubricant to ensure that it doesn't get stuck in the future. Products such as PB Blaster or Liquid Wrench are great alternatives. Apply a thin layer of it and allow it to soak into the barrel of the hinge for approximately 15 minutes.

Refinishing the Hinges

If you are not ready to replace upvc window hinge the hinges on your door, you can do a few simple repairs. The first step is to check whether the screws that secure the upvc window hinge problems plate to the door frame are tight. If they're loose, tighten them with a screwdriver or power drill. Be careful not to tighten the screws so much that they cause gaps at the trim joints, or worse, strip the threads.

If the issue is that the hinge plates are separating from the door and jamb handles and hinges jamb, you can fix the hinges by applying wood glue to the back of the plates and then inserting toothpicks or wooden dowels into the holes. Dowels and toothpicks provide an solid foundation for the screws, preventing the plates from shifting when you insert them. Allow the glue time to dry before reattaching the hinge.

The screws could also be smashed or gone. It is possible to fix this issue by replacing the screws with larger ones. Be sure to use a drill bit that matches the size of the screw hole in order to avoid drilling into other parts of the jamb or hinge.

Once you've reattached the hinge shut the door and check the gap between the door and the frame. The gap should be about the thickness of a penny or less if the old door was not hung correctly. This shouldn't be a problem if the hinges are installed correctly.

If you find that the hinges remain loose, you can try adding a thicker hinge shim between the hinge plate and the mounting surface, to create a little extra space. You could also try taking the hinge pin from the troublesome hinge and then pounding it with a hammer to make it tighter or use the hinge pin from a different angle altogether. It is also possible to lubricate the hinges with mineral or Jojoba oil to lessen friction and assist in keeping their position. Lubricating your hinges regularly can aid in keeping them from becoming stiff or squeaky, and will also extend their life.

Cleaning the Hinges

The friction caused by the constant movement of a hinge attracts dust particles. These particles can get stuck and accumulate over time in the moving parts of door hinges if they are not maintained and cleaned regularly. The window hinge replacement will get stiff and creaky, and its appearance can rapidly change. Regular cleaning, lubrication, and inspection will preserve the integrity and functionality of hinges on a door.

Check the hinges for corrosion. If the corrosion has reached the point of destroying the surface of the barrel or screw holes, you'll have to replace the hinges. If you are able to save the hinges, first brush off loose rust using steel wool and a wire brush. Apply a commercial rust-removing product or homemade solution like lemon juice to the hinge. Allow the rust-removing solution to sit on the hinges for several minutes to penetrate and dissolve the remaining rust.

Retightening screws can help restore hinge function if you don't want to spend time or money to replace hinges. If you've stripped the screws' holes however, it might be necessary to add an wooden dowel or shim to the hinge. Dowels made of wood are square pieces of wood in the form of rods, which are available in different lengths and diameters. You can buy them on the internet, at woodworking supply stores and home improvement stores.

You can also make an shim out of made of plastic or metal depending on the type of hinge you own. To make a dowel cut a piece of wood dowel or another sturdy material to the desired size. You can then dip a dowel into carpenter's adhesive and then insert it into the hole. The glue will secure the dowel in the position.

Before you start cleaning the hinges, lay down a paper or cloth towel to protect flooring and other surfaces from accidental spills and drips. After you have protected the area then clean the hinges using a soft sponge or a cloth dipped into a mild cleaner to remove dirt and grime. You can also remove tarnish, dirt, and grime. A small or toothbrush can be used to access difficult-to-reach places in crevices and difficult areas.