• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

• 페이스북 공유
• 트위터 공유
• 

How to Replace Door Lock Door Locks

The first line of defense is your door lock replacement near me lock. It will stop unauthorized entry to your home. Signs of wear and tear as well as instances like moving into a new house or break-ins, can necessitate the need to replace patio door lock your lock.

You can determine the size of your cylinder by measuring the distance from the center of the knoblock cylinder to the adjustment screw. This measurement will enable you to buy the right lock.

Deadbolt

If you want to make sure your door is safe from criminals, it's a great idea to install deadbolts. The bolt extends into the strike plate on the door frame when it's locked, making it more difficult for burglars to gain entry through the door. A single cylinder deadbolt can be activated with keys on the exterior side and a thumb turn device on the interior. Deadbolts will only work if it is installed correctly.

It is first necessary to determine whether the door already has a hole that is suitable for a deadbolt, or if you have to drill it. With the template included with your lock installation kit, mark the spot of the deadbolt's hole on the door's surface. Use your tape measure to determine the height of the deadbolt. Then, mark the high point on the outside of the door. You can then use the speed square to draw a straight line across the mark you made for the bolt hole.

Then, use a power drill to bore this spot until the hole is on the opposite side of the door. It could take a few minutes. Then, sand down the hole and the edges of the door until it is smooth. At this point, it's a good idea to paint or stain your door.

When the door is in place, remove any screws that are visible on the existing deadbolt. This will reveal both the front and rear assembly of the deadbolt and its internal bolt. Remove the bolt and replace it with the new bolt to match the door hardware. It is necessary to remove the bolt from the setplate. Once this is done then you need to cut out the space for the strike plate on the door frame.

If your strike plate is not in alignment It could be due to the previous installer did not mortise it properly, or a weatherstripping has changed the strike's location. You'll need to re-mortise your strike plate and possibly even the deadbolt to fix the issue. Once this is completed check the deadbolt by closing and locking it. Be sure the bolt is extending into the strike plate, and then test the key to make sure it opens and closes easily.

Knob

If a door knob is worn out it could make your business or home less secure. It may also make it harder to open or close the door, making it a good idea to replace lock in upvc door the knob. It shouldn't take you longer than 30 minutes. You can use a screwdriver or pliers to take off the knob or handle that was previously used Be careful not to damage any other parts on the door.

Spray WD-40 or another dry lubricant, onto the mechanism of your door knob before you begin. This will allow the new lock slide smoothly when you turn it. It's important to use a quality knob and handle that matches your current doors to ensure that the lock is operating properly. If you don't already have a doorknob that matches and handle, you'll need to purchase a replacement.

Before you begin the upvc replacement door locks, look over the knob you replaced to determine which screws are holding it in place. If there aren't any screws you can use a screwdriver to wedge between the cover plate and the screws plate hidden and pop it off.

After removing the old knob examine it for evidence of damage or rust. If the knob has any dents or marks it's time to clean it. Otherwise it shouldn't require any major work.

Install the new knob. You must first study the two knobs in order to make sure that you've selected the appropriate one for your door. You'll need to select one with an extended rod that is interlocked with the rod mechanism of the second knob. After you've inserted the new knob in the hole, slide it into the latch.

Test the spring by pressing it down repeatedly. The latch should spring back up each time. Then, you can install the new knob and lock it with the rod mechanism of the first knob. Then, thread the other long screws from the knob's interior through the hole for the cylinder on the exterior doorknob and lock it in place.

Latch

A latch is a steel piece that extends into the door jamb to keep it shut. It is operated by a knob or handle on the inside of the door, or a thumb turn on the exterior side of the door. The latch can be secured with a deadbolt to keep intrusions from piercing the door's glass. It can also guard against intentional or accidental closing by animals or children. The latch can be fitted with single cylinder deadbolts or a double cylinder deadbolt, depending on the security level you prefer.

Installing a latch follows the same steps similar to installing a deadbolt but there are a few differences. To make sure that the new lock will fit first, measure the setback on the doorjamb using a tape measure. The setback is the distance from the edge of the doorjamb to the middle of the hole for the faceplate for the latch. Setbacks for standard latches are 2 3/8 to 2. 3/4 inches. If your setback is larger than that, you might need to purchase a latch that is longer from a locksmith or hardware store.

Then, make a hole for the latch plate at the edge of the doorjamb. Utilize a chisel to smooth out the mortise for the latch and ensure it's deep enough for the faceplate of the new latch to be flush with the doorjamb. Tape the strike plate in the correct position to ensure it's in the right position.

If the strike is too high, you could push the door back or apply pressure using a tire iron or crowbar. This can also cause the doorjamb to break. To remedy this, the strike could be reduced by drilling a second hole into the doorjamb and chiseling out the core of the previous hole.

Installing the new strike plate is the last step. This can be done by screwing the new plate into the existing screw holes. Then, use wood putty to fill in the holes from the previous screws and the bolt hole that won't be used. After the putty is dry, sand it to a smooth finish.

Strike

The piece of metal that connects the deadbolt and latch when the door is closed is an electric strike. It is a vital part of the lock's security because it prevents the door from opening, and also provides an additional level of resistance to force or kick. If a door is equipped with an electronic strike, it can be opened only by keys and the control unit that regulates the electrical impulses.

Traditionally the installation of an electric strike involved cutting a section of the doorjamb to remotely release a cylindrical lock's latchbolt from the pocket of the strike. This is an issue in terms of the appearance of an opening as well as exposing the latchbolt and keeper mechanism to unauthorized users.

Recently, several electric strike manufacturers have developed an innovative type of electric strike, dubbed the "No Cut" strike that doesn't require cutouts in the doorjamb for operation. These strikes have a unique design that allows the keeper and latchbolt to slide into the strike pocket without damaging the faceplate of the doorjamb.

The strike is equipped with an internal ramp that lifts the latchbolt and keeper whenever it receives an indication from an individual reader. The latchbolt and keeper are pushed up the ramp due to retract. When the door is shut, the deadbolt stays retracted and the latchbolt retracts into the keeper.

Installing an electronic strike is a straightforward procedure, particularly when you're replacing a patio door lock an older strike. If, however, you are upgrading to an electric strike for an access control system, you will be required to ensure that the new system is compatible with the type of lock you've chosen to install. Also, you must make sure that the strike is connected to your access-control system and set up to function in a safe manner.

Upgrade your strike plates to high duty strike plates to block the entry of unauthorized persons. The plates utilize four to six screws of three inches instead of the two three-fourth inch screws that are typically employed in regular strikes. These screws are longer and make breaking the frame to reach the thumb turn piece on a single cylinder deadbolt more difficult.