• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

• 페이스북 공유
• 트위터 공유
• 

How to Replace Door Locks

Your first protection is your door lock. It will stop unauthorized entry to your home. Locks may require replacement upvc door locking mechanism due to signs of wear and tear or other circumstances like moving into a new residence or a burglary.

To begin, you must determine your cylinder size by measuring the distance between the adjustment screw and the middle of the cylinder knob. This measurement will allow you to buy the lock that is right for you.

Deadbolt

Installing a deadbolt is a great way to secure your door from burglars. When the bolt is extended into the strike plate of the doorframe it makes it much more difficult for an intruder to break through the door. A single cylinder deadbolt is activated using keys on the exterior side and a thumb turn piece on the interior. A deadbolt will only work only if it's correctly installed however.

First, you will need to determine if the door has a hole for a deadbolt or if it requires drilling. Mark the location of the hole to install the deadbolt on top of the door using the template included with your lock installation kit. Then, use your tape measure to determine how high the deadbolt needs to be. Mark this high point on the door's edge, and then use speedsquares to draw a straightline across the mark you made to mark the bolt hole.

Then, use a power drill to bore out this spot until the hole is on the other side of the door. This may take a while. Sand the hole and edge of the door to make it smooth. At this stage, it's a great idea to stain or paint your door.

Remove any visible screws from the deadbolt. This will reveal the front and back assemblies of the deadbolt, and also the bolt inside. Then unscrew the old bolt and replace upvc door lock it by a new one to match the door hardware. The bolt is often connected to a set plate, which you will need to unscrew. Then, you'll need to chisel the surface of the upvc door locks replacement frame for the strike plate.

If your strike plate is out of alignment, it could be because the previous installer failed to mortise it properly, or a weatherstripping has changed the strike's position. It is necessary to re-mortise the strikeplate and perhaps even the deadbolt to fix the issue. After this is done Test the deadbolt by closing it and locking it. Test the deadbolt by closing and locking it once the bolt has been extended into the strike plate.

Knob

It could make your home or business less secure If the knob on your door is worn. It can also make opening or closing the door more difficult, which is why it is recommended to replace door lock - just click the following webpage - it. Replacing a knob is a relatively easy DIY project and shouldn't take more than 30 minutes to complete. You can use a screwdriver or pliers to get rid of the knob or handle that was previously used However, be careful not to damage any of the other components on the door.

Spray WD-40, or another dry lubricant, on the mechanism of your door knob before you begin. This will allow the lock to move effortlessly as you turn it. To ensure that it operates properly it is important to select a knob and handle that match your existing doors. If you don't have a match then you'll have to purchase a replacement doorknob and latch plate.

To begin the replacement locks for patio doors process, first look at the knob or handle to determine what screws hold it in place. If there are no screws, you can use the screwdriver to insert the cover plate in between the screws plate hidden behind it.

Once you've removed the old knob, examine it for any signs of rust or damage. If the knob has any scratches or marks, you'll have clean it. Otherwise it shouldn't need any major work.

Install the new knob. Before you do that, look over the new knobs to ensure you're picking out the right one for your door. You should select one that has an extending rod that's designed to lock into the rod mechanism on the second knob. After you've placed the new knob in the hole in the door and then carefully slide it into the latch.

Test the spring by pressing it repeatedly. The latch should then spring back up every time. Then, you can install the new knob and connect it with the rod mechanism on the first knob. Thread the long screws of the interior doorknob through the holes for the cylinder on the exterior knob, and lock it into the knob's position.

Latch

A latch is a piece of metal that extends into the door jamb to keep it closed. The latch is operated by a knob or handle on the inside of the door, or by a thumb-turn on the outside. The latch can be secured with a deadbolt to keep thieves from breaking through the glass. It also helps protect against the accidental or deliberate closing by children or animals. You can choose to install a latch with either a single-cylinder or double-cylinder deadbolt depending on the level of security.

Installing a latch involves the same steps similar to installing a deadbolt however, there are a few variations. To make sure that the new lock will fit, first determine the setback of the doorjamb using a tape measure. The setback is measured from the edge of the doorjamb up to the center of hole for the latch plate. Standard setbacks are 2 3/8 to 2. 3/4 inches. If your setback is greater it is possible to purchase an extra-long latch from a locksmith or hardware store.

The next step is to drill an edge bore hole into the doorjamb for the latch plate. Utilize a chisel to cut the mortise of the latch. Make sure the hole's depth is enough to allow the faceplate to be flush with the doorjamb. Place the strikeplate on the floor to ensure that it's positioned correctly.

If the strike is set too high, the door could be pushed in or pressure imposed on it using a crowbar, or tire iron. This can cause the doorjamb to break. To correct this, the strike can be reduced by drilling a second hole through the doorjamb, and then chiseling out the center of the hole that was previously drilled.

Installing the new strike plate is the last step. This can be done by screwing the new plate into the screw holes that are already in place. Utilize wood putty to fill in any existing bolt holes or screw holes which aren't going to be used. After the putty is dry then sand it to a smooth finish.

Strike

An electric strike is a metal piece that holds the deadbolt and latch engage when the door is shut. It is an essential part of the lock's security because it prevents the door from opening and gives an additional level of resistance to force or kick. If a door is equipped with an electric strike, it can only be opened with an entry key or the control unit that controls its electrical impulses.

Traditionally the installation of an electric strike required cutting out a portion of the doorjamb in order to remotely remove a cylindrical lock's latchbolt from the pocket of the strike. This is not only undesirable and unattractive, but also exposes the mechanism of the latchbolt and keeper to uninitiated users.

Recently, a number of electric strike makers have come up with a new type of electric strike dubbed the "No Cut" strike that doesn't require cutouts in the doorjamb to operate. These strikes have a unique design that allows the keeper and latchbolt to slide into the strike pocket without marring the doorjamb faceplate.

The strike is fitted with an internal ramp which lifts the latchbolt and keeper whenever it receives the signal of an individual reader. The retracting of the keeper as well as latchbolt pushes them up higher on the ramp, thereby locking the door. When the door is closed the deadbolt remains in place and the latchbolt is retracted into the keeper.

Installing an electronic strike is a straightforward procedure, especially in the case of replacing a upvc door lock an existing strike. However, if you are upgrading to an electric strike for an access control system, you will have to ensure that your new system is compatible with the model of lock you've chosen to install. You will also need to ensure that the strike is connected to your access control system and is designed to operate in a fail-safe manner.

One way to protect against unauthorized access is to upgrade the strike on your doors to a robust strike plate. These plates are fitted with four to six screws of three inches instead of the two, three-fourth inch screws typically employed in regular strikes. These longer screws make breaking the frame to reach the piece that turns the thumb on a single deadbolt for a cylinder more difficult.