• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

• 페이스북 공유
• 트위터 공유
• 

How to Replace a Kia Sportage Replacement Key

The key of many kia sportage Replacement Key fob models comes with a keyless entry system built in. This key is similar to remote controls, and is exchangeable by an Kia dealer.

Key fobs can stop working due to a variety of reasons, including a dead coin battery, worn buttons, signal interference, water damage, and a defective receiver module. Here are some helpful tips to assist you in getting your Kia key fob that is a replacement for the sportage again.

how to find lost kia key do you replace the remote key or the smart key?

Whether your Kia comes with an intelligent key, remote key, push-to-start key, or a regular non-transponder metal key The battery inside these keys will eventually require replacing. This is particularly true if the car displays a message that the smart key or remote is not powered by the battery.

This is a relatively simple procedure. To replace the battery in the keyfob remove your mechanical key from the slit that is located at the back of the fob. Then, push the cover off. Inside the key fob will be tiny screws that hold the battery in the correct position. Remove the old battery by removing the screw using the help of a small screwdriver. Install the new battery and close the opening on the key fob.

Once the key fob has a fresh battery Test it by pressing the lock and unlock buttons. If the doors unlock and lock as expected, then you're all set! You can now use the Kia's hands-free lock/unlock feature whenever your fingers get chilly or you need to make errands in Brandon.

Note: Certain key fobs could need to be programmed (transponder chips or smart keys). This requires a programing machine, which is only available to the locksmith for cars or dealer. Other keys (non transponder keys made of metal) don't require programming. If your key has to be programmed again, you will need to be aware of the key code number printed on the tag that identifies the key and record it in a safe place.

How to replace the battery

If your Kia key fob is not responding when you press the lock or unlock button on the fob, this is a clear indication that the battery needs to be replaced. A low battery could cause other issues, such as the check engine light coming on or a delay in cranking the engine. Fortunately replacing the battery on the key fob is a fairly simple DIY project that requires only a few tools.

Make sure you turn off your vehicle and close all doors prior to starting. Locate the small metal or plastic piece that is on the bottom of your key fob, and gently jiggle it until the metal key slips out. This key can be put into the driver door handle to unlock your car.

To replace the battery in the key fob remove the cover at the rear. Use a pry tool to open the latch that holds the black negative cable. Remove the old battery and then orient the new one so that the "+" positive side faces your face and the "negative" negative side is facing towards the fob's electrical contacts made of metal. Push the new CR2032 battery straight into position with care to avoid using too much force to avoid bending or damaging the metal contacts.

After the new battery has been installed then turn the key fob off and on in the ignition repeatedly until the door locks. You can then test the kia soul key fob's Key fob again to confirm that it's working properly.

How can you replace the smart key

Depending on the model of the Kia Sportage, you may have an ordinary key fob or a smart key. The smart key has an embedded mechanical key blade, while the standard keyfob does not. Both key fobs come with a battery that will eventually require changing. Fortunately, it's an easy process that takes only two minutes.

Before you start it is essential to make sure that you are on a flat surface with adequate lighting and that the Kia is off. Keep in mind that there are tiny components inside the fob which could fall out if you are not careful.

The first step is to locate the small release button on the lower backside of your fob. This will be either a circular or rectangular slot. You can open the key fob by pressing the button.

Once you have the key fob opened, you can simply take out the old battery and replace it. The new battery is a CR-2032 that can be bought online or from your local auto parts store. Once you're done it should be possible to lock or unlock your vehicle with your key fob - even if the engine isn't running!

How do you replace the mechanical key?

The Kia key fob is a fantastic option that lets us lock and unlock our car at the push of an button. Like any other device there are issues with it at times. Luckily, there are methods to troubleshoot these issues and ensure that our key fobs are in good working order for the long term.

One of the most common problems is a weak or dead battery. This can cause your device to stop working or work intermittently. If this happens then try replacing the battery with a new one.

If this does not solve the issue, try using the flathead screwdriver that is standard to push the fob's casing made of plastic open. Be careful not damage any internal components, or scratch the plastic. After the battery has been removed, replace it with a brand new one.

After the new battery has been put in, shut and open the doors with the mechanical key (every 2013 kia optima key fob programming fob has an emergency mechanical key that will fit in the slot). Test the key fob and make sure it is working properly. If the key fob isn't working, call a dealer or locksmith to solve the problem. Make sure they make you an emergency key that works for all trunk and door cylinders to avoid lockouts in the future.