• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

• 페이스북 공유
• 트위터 공유
• 

Glass Window Repair

Professional window repairmen work from high above the ground, navigating huge glass panes. They work in extreme weather conditions and follow strict safety guidelines.

Wearing protective clothing, take off the metal glazing points as well as all glazing putty with an utility knife. A heat gun can help to soften and take off the old putty.

Replacement

When a window's pane breaks, it can be tempting to repair double glazing window the glass rather than replace it. It is cheaper to replace a window, and it can also help you to avoid other issues in your home's efficiency. It is also important to consider the type of glass that is broken to determine if this is a temporary fix or if you'll need to invest in an option that is more permanent.

To repair a broken window, you must remove the frame or sash, and place it flat on your work surface. Wearing eye protection, gently wiggle and pull out any shards remaining in the window. Utilize a utility blade repairs to double glazed windows remove the glazing compound, and the glazing points that hold the window in place. Be sure to keep track of the components and their locations to ensure that they can be reinstalled later.

After the frame and sash are removed then you can begin the process of preparing to install the new glass. Be sure to check that the opening of the frame is the right size for the replacement window. Measure both sides of the opening, and then subtract 1/8 inch from each measurement in order to leave room for expansion and contraction of the frame and glass. Then, buy double-strength glass cut to these precise dimensions. It is recommended to purchase enough glazier's clips, or points to place them every 6 inches around each window pane.

Depending on the window's warranty the window may be covered by the manufacturer and in this case, you must contact the company to file an claim. After the new glass has been erected it is crucial to cover it with a thin layer of glaziers compound. After letting the compound dry and dry, you can paint it to match the rest of the window frame.

If your crack is more than an inch in length, you can prevent it from expanding by scoring the crack with a small arc, just above the crack. This technique isn't 100% foolproof, but it can slow the growth of the crack down to a manageable amount until you can take more permanent measures.

Repair

Professional window contractors are equipped with the proper tools and know how to handle various types of glass. They also know the best methods for disposing of waste, so they're less likely to leave scraps behind, which could potentially hurt pets or family members. They're also familiar with different types of windows and may be capable of identifying issues that aren't obvious to a homeowner who isn't experienced.

Wear safety glasses and gloves prior to beginning repair work on cracked glass. Even a small crack can cause glass shards to fly and put anyone at risk in or around the home. It is crucial to determine what caused the crack, so that you will help prevent any future problems.

Make a two-part mixture of epoxy. They are typically 50/50 mix of hardener and resin, and they must be mixed quickly. When the mixture is done, apply it to the glass crack and leave it to dry. This should only take about a minute but it's important to get it done quickly as the mixture is extremely thick and fast-drying.

After the epoxy has dried, you can remove excess epoxy with a putty blade. After that, you'll need clean the area around the crack of glass. If you don't clean the area in a proper manner the residue could cause further damage to the glass. Use a putty blade to smooth out the compound around the edge of the window and then match it to the frame made of wood.

You could consider using a plastic cover for a more robust option. You can cover the glass using masking tape or a heavy-duty trashbag. This will prevent the crack from spreading, and will also keep water, wind and bugs out.

You can make a temporary fix when you are unable get to the window in a timely manner. Simply run a bead of the material around the outside of the broken window. It won't completely fill the gap between frame and glass but it will help keep the break in place while you repair windows it.

Repainting

If your windows with glass are old, you may consider repainting them. This is a low-cost alternative to replace your windows and will provide your home with a new look. Make sure that the surface is clean before painting. Use soap or rubbing alcohol and water to get rid of oil smudges and other residues that could prevent paint from adhering. Wear rubber gloves while working on glass to prevent the transfer of your own oils onto the glass surface. Finally it is recommended to apply several thin coats of paint instead of a single thick layer. This will help the paint last longer and will keep your windows looking smooth and even.

Make sure you have the right tools in your arsenal when you are planning to repaint glass windows. You'll need brushes or sponges as well as a painter's tamper, a ruler and toothpicks. You should also have the brushes and paint you'll be using for the project in your possession. Follow the instructions of the manufacturer. Have patience, as it may take a while for the paint to fully dry.

You should also make sure the space you're working is well ventilated if you're using solvent-based paint. This will decrease the risk of breathing into toxic chemicals and allow the paint to dry faster. Use a mask that is protective when using spray paints.

For older glass windows, it is necessary to prepare the surface prior to painting. Use soap and warm water to thoroughly clean the glass window. Then, use rubbing alcohol on any oil or grease residues that could interfere with the paint's adhesion. Make sure that the windows are completely dried before you begin painting them.

If you have energy-efficient double pane windows on your windows, it could be possible to make a claim for repair or replacement with the company that makes the windows or dealer that sold the windows. This is especially true if you have experienced numerous issues with cracked glass or condensation even though the windows are covered by warranty.

Sealing

There are a variety of options to fix the problem depending on regardless of whether you have an old double-pane window with a cracked seal, or if you have an upgraded insulation unit (IGU) that has experienced defogging. It is the most expensive option to replace the insulation unit and the frame. However, it could be necessary in cases where fog or condensation is creating energy losses. Other options include replacing the IGU with just one pane, or repairing the existing IGU by drilling a hole through the bottom and filling it with an anti-fogging product.

You can also fill in the gap between windows and a threshold or sill by with a felt strip or vinyl v-strip. Felt is inexpensive and can be fixed by gluing, nailing, or stapled into place, but it does not offer much protection against moisture. Vinyl v-strips are simple to install and long-lasting, but can be expensive. It is typically reserved for areas exposed to abrasions that are high. Door sweeps are cheap and can be fixed into place, but they create little to no barrier between the sill or threshold and dust, air, and debris.

To repair a damaged window seal first, use a putty blade to remove the old caulk. Wearing eye protection and gloves, carefully pry out the glazing points -- small fasteners that pin the glass in the frame's recess using sharp, pointed edges. After you have removed the glazing points, clean the grooves and sand the wood to a smooth finish. Wipe off any sanding traces, then seal the bare wood using a linseed oil-based paint or clear wood sealer.

Traditional glazing putty can be applied with the help of a putty blade or caulking gun, however a knife provides a better, more precise application and provides a stronger seal. Choose a putty specifically for glass, since it will last longer and stick better.

Apply a small amount of the putty to the inner edge of the frame where it meets the glass. Slide the window into the frame in a way that the drawn line on the glass is aligned with the edge of the frame. Apply pressure to the glass to press the putty and create a tight seal. Smooth the compound with a gloved finger, and wipe away any mistakenly applied caulk or spills that are not properly wiped away before it dries.